Question about Ruud Heating & Cooling

2 Answers

Purchased new motor from Grainger motor has 4 wires 1 BLACK 2 BROWN 3 BOWN WHITE 4 YELLOW had to purchase new capasiter also for motor Old motor only had 3 wires 1 BLACK 2 BROWN 3 ORANGE Need to know how to connect the wires from the new motor to my unit and to the new capacitor ???

Posted by on

  • 2 more comments 
  • usafamily4 Oct 01, 2009

    Thanks Rylee it looks like it will help me, but I just discovered the wires being to short, what do you suggest I do ??

  • usafamily4 Oct 01, 2009

    I would also like to know if this is the right contactor for this unit if so where could I buy one ? The model number is VAND 024JAZ the serial number is S7293M160622155 on the contactor are two numbers 3100-15Q103 and 42-42139-05 . The coil is 24VAC 50/60HZ 5MFD 370VAC THANK YOU SO MUCH in advance

  • usafamily4 Oct 01, 2009

    Thanks Todd. you helped a lot

  • usafamily4 Oct 08, 2009

    Great salution, thanks Grainger was very helpful

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 247 Answers

Grainger has great tech support,call them first,i would have to do the same to answer your question accuratly,im assuming it is the condenser fan motor,they will have all the correct info,if not i want to know,i was born and raised in minnesota and have dealt with grainger for 25 years.,moved to maui 6 years ago. that wont stop me from making a phone call and chewing their ***..doubt that will be necessary,but if you have problems send me a note,aloha from maui todd0708

Posted on Oct 01, 2009

  • todd gentile
    todd gentile Oct 04, 2009

    any time ,were you able to wire in the new motor?

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,619 Answers

Hi
Thanks for using FixYa. Please see this diagram on how to connect wires:
purchased new motor from Grainger - airdiagram.jpg
1dd5e59.jpg


Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks Rylee

Posted on Oct 01, 2009

  • Rylee Smith
    Rylee Smith Oct 01, 2009

    Hi




    Please see these links for parts for your unit--


    Rudd/rheem replacement parts




    You can also check this listing for parts prices and orders---




    Replacement coils




    Please do accept the solution if the issue is resolved or else revert for further assistance.



    Thanks



    Rylee

  • Rylee Smith
    Rylee Smith Oct 01, 2009

    Please do accept the solution if the issue is resolved or else revert for further assistance.


    Thanks

    Rylee



×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Old motor wires are numbered new motor wires are colored this is a 1/2 hp reversing motor for a overhead door


Single Phase Terminal Markings Identified By Color: (NEMA Standards) 1-Blue 5-Black P1-No color assigned 2-White 6-No color assigned P2-Brown 3-Orange 7-No color assigned 4-Yellow 8-Red

Mar 02, 2014 | Computers & Internet

1 Answer

Replaced a ge condensor fan 3 wire with new dayton the wires are different...old fan has a wire connectort mouted to it orange,black yellow, the new one 2brown 1 with white stripe, purple, black, i have...


the new ge fan requires its own capacitor, the brown and the brown/white go direct to new fan capacitor. black to relay (leg one of power) purple to relay (leg two of power. the compressor will have a wire to the relay and the other to the herm terminal. you now will have nothing to the original capacitor fan terminal.
The new motor will have the diagram showing this. you need the capacitor that goes with the new motor. the grainger guy should have sold that to you with the motor.

Apr 11, 2013 | Heating & Cooling

1 Answer

I have a general lee cb with a 4-pin standard mic. the wires in my mic cord broke at the plug. does wnyone know how to wire this type of mic back and what color wires go to the correct pin?there are 6...


Here are the Pin outs for different mics that will work with your radio. If a wire is not listed then you cut it off. It's best to keep the wires as short as possible no longer than a half inch is suggested. Normally the Cobra pin out is standard for most radios.

Stock - 1- Shield (Ground) 2- Yellow (Audio) 3- Red (Transmit) 4- White (Receive)

Astatic - (4 wire) 1- Shield 2- White 3- Red 4- Black

Astatic - (6 wire) 1- Shield & Blue 2- White 3- Red 4- Black Yellow NC

Daiwa EM-500, Cobra, CA Series - 1- Shield & Black 2- Red 3- White 4- Blue

Galaxy DC-521S - (4 wire) 1- Shield 2- Yellow 3- Red 4- Black

Galaxy CB-660EI - 1- Shield & Black 2- White 3- Red 4- Blue

Sadelta - 1- Shield 2- White 3- Brown 4- Green

Turner - 1- Shield & Red 2- White 3- Blue 4- Black Yellow NC

Jul 12, 2011 | Magnum DeltaForce CB Radio

1 Answer

I need the wiring for the mic


Hello,
Here is the wire diagram for several common mics in relation to a 4 pin CB. Most recent 4 pin CB's such as Midland, Cobra, Connex, Uniden, etc can use 4 pin mics. The wiring is actually depending on the mic rather than the CB so long as the CB's are 4 pin as well. Once you go back to late 80's the 4 pin design was a little different. Anything new it is simpler.
Stock Mic 1- Shield (Ground) 2- Yellow (Audio) 3- Red (Transmit) 4- White (Receive)
Astatic - 4 wire 1- Shield 2- White 3- Red 4- Black
static - 6 wire 1- Shield & Blue 2- White 3- Red 4- Black Yellow NC

Daiwa EM-500 Cobra CA Series 1- Shield & Black 2- Red 3- White 4- Blue
Galaxy DC-521S - 4 wire 1- Shield 2- Yellow 3- Red 4- Black
Galaxy CB-660EI 1- Shield & Black 2- White 3- Red 4- Blue
Sadelta 1- Shield 2- White 3- Brown 4- Green
Turner RK56 Road King 1- Shield & Red 2- White 3- Blue 4- Black Yellow NC
Regards, Tony

Apr 07, 2011 | Connex Radio Communications

2 Answers

Unsure of capacitor terminations for ao smith condensing fan moto


Does the motor data plate say anything about the motor. You can hook up a motor like yours with 3 wires. First use an ohmmeter and check the resistance between the brown/white wire to the black then the yellow wire. The resistance between brown/white and one of the others should be pretty much 0 ohms. If not check between the brown wire and the black and the yellow. Which ever wire has 0 ohms with the brown/white wire is the common leg. You can put a wire nut on the brown/white, it will not be used. Next the brown should be for the start winding and the other wire left over will be the run winding. Then connect the common to L2. L1 will go to the run winding and one side of the capacitor and brown will go to the other side of the capacitor. I hope this isn't too confusing. Let me know if I need to explain it better.

Jun 09, 2010 | Heating & Cooling

1 Answer

I just purchased an fse1028sf to replace my faulty fan motor. I purchased it from a a/c supply store. My existing fan only had three wires. They were brown, black and purple. Black to: capacitor "c"....


Hi, this is a different wiring diagram then what you have . The 2 brown/wht wires are for the run cap only. Black and white are t-1 and t-2. They sold you a motor that takes its own run capacitor to run it with just both brown wires. Take the diagram from the new motor back along with your original. They will give you the right run cap to go with this motor. Yes, the red wire is power to fire your existing cap and old motor. You will need another cap to run this motor. Don't put the 2 brn/white striped wires on the old cap! They have to be alone on there own run cap. Go back to the parts house and they will show you very fast the wiring diagram and give you the cap. This is a very easy fix when they give you what you need. Keep me posted and ask them to give you what you need to run the motor. A 5 uf run cap perhaps?
Keep me posted.
Shastalaker7

May 03, 2010 | Heating & Cooling

2 Answers

Wiring a TPH553 Surface Mounted Jack by RCA.


TPH553 T568A T568BPin 1 - BL White/Green White/Orange Pin 2 - OR Green Orange Pin 3 - BK White/Orange White/Green Pin 4 - RD Blue Blue Pin 5 - GR White/Blue White/Blue Pin 6 - YL Orange Green Pin 7 - BR White/Brown White/Brown Pin 8 - WH Brown Brown
REF: wikipedia

Feb 17, 2010 | Computers & Internet

1 Answer

Wires


2 brown wires go to a split capacitor if you have a dual cap which has three terminals marked comp fan com if u have this type of capacitor then the brown wire goes to fan and the brown and white gets capped with a wire nut. whenever replacing a fan motor you should also replace the cap or at least check the capacitance to see if it is still good. you have to check it with a meter that test microfarad.you can get a permanent split capacitor and mount it in there then u use the brown on one side and the brown and white on the other side it only has 2 terminals.

May 31, 2009 | GE Heating & Cooling

1 Answer

HELP!!! Help wiring new motor for CKL60-1


  1. This is what your wiring should look like if you are using two caps. then you should be using a potential relay as well. This is the diagram for using a potential relay. Hope it helps you.
Thank Youe461749.jpeg

Aug 25, 2008 | Goodman CKL60AR60 Air Conditioner

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ruud Heating & Cooling Experts

Donni Steen

Level 3 Expert

659 Answers

Bill Long

Level 3 Expert

587 Answers

Tim Whalen

Level 3 Expert

3072 Answers

Are you a Ruud Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...