Question about Zebra Eltron Orion LP2443 Thermal Printer

1 Answer

Won't print quit printing, I do a test print and just get 3 blank labels

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

This printer is Thermal Direct (DT) only (ie it does not use a ribbon, the paper is thermally sensitive).

Check your labels are DT material by quickly running the edge of your fingernail across the surface. If it leaves a black mark then it is the right material, if no mark then it is not the right material, contact a label reseller for DT labels.
ie www.lancerlabels.co.uk

Posted on Jan 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printing blank label


You need to give more info.

Are you using labelling software?

Dec 06, 2015 | Zebra Z6M Plus Thermal Label Printer

1 Answer

Label is printed fine but each printed label print blank line before label print


To isolate problem run a test label from printer.Does the same thing happen? If so it is a printer problem.If not the problem is in the document itself.

Apr 24, 2014 | Zebra LP 2844 Thermal Printer

1 Answer

My printer is printing 3 blank labels before printing the correct label?


Sometimes it's the Internet Browser (if you are printing from an Online Software) and by clicking File ' Page Setup you can make sure margins are set to 0.1 (or as close as possible it may override you) and all six bars below (headers and footers) should be switched to Blank.

Apr 12, 2013 | Zebra S4M Thermal Label Printer

1 Answer

I have a Zebra Z4M printer. We use it to print on various labels - pre-printed and blank labels (semi-gloss). I've been struggling to print on one of the pre-printed labels. Everything else prints...


some labels are hard to calibrate, nee to calibrate the sensors with manual calibration.
1} go to the MEDIA AND RIBBON CALIBRATION,
2}take 2 or 3 labels from the base paber, load the way to the based paper stay unther the sensors, 3}close printhead.
4} press ok.
5} Move the ribbon out from sensors and close the printhead.
6) press ok
7) wen printer ask RELOAD ALL, load the labels correcly and the ribbon, close the printhead and the top door, and press ok. The printer run the calibration it self.
wen finish, saved (press setub twice) and test.

Jan 21, 2011 | Zebra Z4M Printer

1 Answer

Label double print


It's possible that the printer did not get a good calibration on the size of the label. There's an optic sensor looking for the gaps in the labels. A test would be to turn the printer off and back on again. When it is ready, just press the feed key. If one label advances then the printer had a good read on the label size. The idea is to see if the printer works ok by itself first.

Now print a label - if you get two labels then you have to look at the software / printer driver as the cause. The printer will only do what it's told to do.

Hope that helps !

Apr 14, 2010 | Zebra LP 2844 Thermal Printer

1 Answer

Loftware labels printing off staggered.


Most reasons for this is a slight adjustment problem with page length. You can recalibrate the printer via the menu system, doing it this way will adjust the sensors with new settings

Mar 11, 2010 | Zebra Eltron TLP 2844 Thermal Label...

1 Answer

Labels are blank


Check first ribbon and the label are OK. After check the darkness settings are correct. And finally prints a test print.

Mar 13, 2009 | Zebra 110PAX4 Thermal Label Printer Print...

2 Answers

Labels printing in reverse order


It's not the printers, has to be the software.

Contact your vendor for support.

Steve

Mar 04, 2008 | Zebra Stripe S600 Thermal Label Printer

Not finding what you are looking for?
Zebra Eltron Orion LP2443 Thermal Printer Logo

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

pkwc

Level 2 Expert

254 Answers

Dave Busselle

Level 1 Expert

54 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...