Question about Kodak EASYSHARE 5500 All-In-One InkJet Printer

1 Answer

Software Won't finish installation

Windows XP system
I cannot get the software to finish installing. It will go so far through & then gets a 40-20-0? error and tells me it can't complete the set-up. I also don't seem to have a driver for this printer. the install wizard says there is no information on the set-up disk about this printer? Now I tried following the online troubleshooter from the easyshare site and I still have the same problems. I updated to windows installer 3.0, same problem. used the cleaning utility many times, same problem. This is very frustrating any help would be greatly appreciated!

Posted by on

  • Dianalyn Dec 27, 2007

    So I take it you need the "Premium Assistance plan" to get help with a problem?

  • Dianalyn Dec 29, 2007

    Contact Kodak tech support, they helped me get mine installed and it didn't cost anything.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Upgrade to the latest software and firmware from the Kodak website.

http://www.kodak.com/global/en/service/downloads/dln_ekn033541.jhtml?pq-path=10624

Uninstall old software from "add or remove" programs and make sure usb cable to printer is unplugged when you re-install software.

Posted on Feb 08, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Plustek OpticFilm 7600i SE film scanner. Every time I try and load-up the setup disc, the set up install starts and then comes up with this error message: An error (-500 : 0x8004ace8) has...


It is quite possible that there is another piece of software that is clashing with your Plustek OpticFilm scanner. It is hard to tell which software is having a clash. If you remove that software from your system you will obtain the desired results. I suspect the SP3 of Windows XP may be responsible for this because Microsoft has indicated that Windows XP SP3 is not for everyone. If you install Windows XP SP2 uninstalling XP SP3 your problem can definitely be rectified.
Good Luck!

Mar 10, 2011 | Plustek OpticFilm 7200 Film Scanner

1 Answer

I want window vista BUT I DONT KNOW HOW CAN I DO THIS


Hi there !

So tell me, what do you want to do with your computer? Do your computer crash and need to reinstall your Windows Vista operating system? Or you want to upgrade your operating system from Windows XP to Windows Vista.

For reinstalling Windows Vista, is it the same procedure when reinstalling Windows XP and Windows 7. Here is the link on how to reinstall operating system http://www.fixya.com/support/r7410371-reinstall_windows_xp_or_installing_clean. For Windows Vista, here is the procedure on how to reinstall Windows Vista.

1. Just put the installer CD into the CDROM Drive and open your computer
.
2. If message appear to press any key to boot from CD. Press any key to go to Windows Set up.

3. From there, just follow the installation procedure and put CD key if prompted and it will install itself the whole process. It will reboot for 3 times and don't press anykey when this happen. it will be finished within 20 mins.

For upgrading from Windows XP to Windows Vista, remember that all your files and softwares will be remove except for the hardware drivers. But not all the hardware drivers will be 100% working because upgrading the operating system will make your drivers outdated or not compatible with Windows Vista. If some drivers not working, just install the hardware drivers compatible with Windows Vista.

Here is the procedure.

1. Do not put the Windows Vista installer CD yet into the CDROM drive.

2. Open your computer and let it run to Windows XP program until is is finished to load your Windows settings.

3. Now insert your Windows Vista installer CD to the CDROM drive, it will pop up the upgrade installation wizard and just choose the upgrade installation. It will run the upgrading installation and just follow the instruction and it will be finish with 20 mins.

I hope this will help you and thank you for using FixYa !

Jan 07, 2011 | Computers & Internet

1 Answer

My problem is exactly the same.


Here is the newest verison of the the Nintendo wifi usb stick driver:
http://www.nintendo.com/consumer/systems/wii/en_na/onlineUSBDownload.jsp

And here is the manual that describes how to install the driver:
http://www.nintendo.com/consumer/systems/wii/en_na/connectingOnline.jsp?entryId=usbInstall

Not your only able to install unsigned drivers on Windows XP and Vista 32Bit versions.
64Bit versions of Windows XP and Vista won't accept unsigned drivers at all.
On windows vista and xp chose to continue to install te unsigned driver when windows prompts for it.

Succes.

Aug 31, 2009 | Nintendo Video Game Consoles & Games

1 Answer

Editing text


s.gif Select from the list below s.gif s.gif s.gifs.gif

Windows
» HP Scanjet Scanners Supported and not Supported in Microsoft(R) Windows XP s.gif » Resolving 'Missing MSIEXEC.EXE File is Linked to Missing Export: MSI.DLL.222' Error Message During Installation of the HP Director Software s.gif » Resolving 'Scanner not supported' or 'Unsupported operating system' Error Messages s.gif » Resolving Image Zone Install Error 1402, 1406, 1714, 1904, 1935, 2203, or Unknown Error s.gif » Error 'The System Cannot Find the File Specified' While Attempting to Install the HP Photo & Imaging Software in Windows 98, 98se, or Me s.gif » 'Cannot Install This Hardware - The Required Section Was Not Found in the INF' Error Message in Windows XP s.gif » 'Error Install Failure' Message for the hpznfx01.exe Software Module Displays on the Computer When Installing HP Image Zone s.gif » The message 'Fatal error during installation' or 'Error Install Failure' Occurs When Installing HP Image Zone s.gif » A 'Fatal Error' or 'Error_Install_Failure' Error Message Displays on the Computer When Installing the Image Zone Software s.gif » The Error Message 'Error_Install_Failure' or 'Fatal Error' Occurs when Installing Image Zone Software s.gif s.gif
Macintosh
» Mac OS: Software Driver Install Causes Error, "Interface Lib Get Component Resource Could not be Found" s.gif » 'Cannot Install This Hardware - The Required Section Was Not Found in the INF' Error Message in Windows XP s.gif » 'Scanner could not be initialized' Message Displays in Mac OS X when the All-in-One Software is Installed s.gif » Mac OS: Software Driver Install Causes Error, "Interface Lib Get Component Resource Could not be Found" s.gif s.gifs.gif

Jun 13, 2008 | HP 4570C Flatbed Scanner

2 Answers

Cd rom message "no emulation" when booting the windows xp installer


when i install my windows xp professional i get a message prompting BOOT TO ATAPI CD-ROM: "NO EMULATION".... how can i fix this?Pls help me on this

Jun 07, 2008 | ASUS P4SP-MX Motherboard

2 Answers

Missing Operating System error


your bought compag computer is a new one , because that error is appears only if the hard drive or the harddisk is defective or damage. Your installation of windows xp is finished totally because sometimes the error is appears because the system installation is not finished and the os system cannot read. try to re install again the windows and delete the old partitions and create again if the problem is the same even there is no error in the installation until it's finished i say that the problem is in the harddisk. Maybe the harddisk develop a bad sector in the master boot record of the hardrive

Apr 15, 2008 | Compaq Presario 700 470024-192 Notebook

1 Answer

How to configure my MSI 865PE Neo3-F and Install an Operating System?


Check your Hard Drive with diagnostic software.
Test your memory with diagnostic software.
Been using this board with Windows XP for over a year with no problems at all.

Jan 15, 2008 | MSI 865PE Neo3-F Intel 865PE LGA775 DDR...

2 Answers

Software won't work with vista


Uninstall Windows Vista. Do a fresh install of Windows XP Professional Sp2. Download XP drivers and install camera. Many software programs have trouble initializing in Windows Vista. Good luck!

Oct 12, 2007 | Microsoft LifeCam VX-6000 Webcam

1 Answer

Can I use the PDC 1100 camera with Windows XP?


Yes, you can use the camera with Windows XP, but you will no longer be able to use a USB port to download your photos. Only serial port downloads are supported under Windows XP for the PDC 1100 camera. Follow the instructions below to reinstall the PhotoMAX software and camera drivers using Windows XP's Program Compatibility Wizard. 1. Insert the PhotoMAX CD-ROM in the CD drive. If the program begins installing, press OK to close the "not compatible with Windows NT" error message. 2. Start the Wizard by clicking the Start button and choosing All Programs > Accessories > Program Compatibility Wizard. Follow the on-screen prompts. 3. On the second screen, select I want to use the program in the CD-ROM Drive and click Next. 4. Select Microsoft Windows 98/Windows Me and click Next. NOTE: You may have to scroll down to see this option. 5. Uncheck the following items: * 256 colors * 640 X 480 Screen Resolution * Disable Visual Themes 6. Click Next. 7. Click Next again. The PhotoMAX software will begin installing. Follow the on-screen prompts. 8. Follow on-screen prompts to finish the installation and click Finish. 9. When the Compatibility Wizard asks if the program worked correctly select Yes and click Next. 10. When the program asks if you want to send information to Microsoft, select No and click Next to finish the installation. 11. Shut down and restart the computer. After the restart, you should be able to download photos using Windows XP.

Sep 14, 2005 | Polaroid PhotoMax PDC 1100 Digital Camera

1 Answer

Problems with installing Active Sync on Windows xp.


Do you use companion CD for Active sync installation? Can you please tell me which driver is necessary to have? Is there any error message and what is content of this message? It can also be that Active Sync is already installed! Please check at Add and remove Software in Control panel! Otherwise go to www.microsoft.com and download a current version of active sync

Sep 11, 2005 | Toshiba e400 Pocket PC

Not finding what you are looking for?
Kodak EASYSHARE 5500 All-In-One InkJet Printer Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Cindy Wells

Level 3 Expert

5582 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...