Question about Pool & Spa

1 Answer

Layz spa keeps going off says on readout 6cf.heater is fine pump everything else is ok cheers kevin

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

You have a problem with the RCD (residual-current device). This is the part of the plug that you have to push reset on before a current will flow. You can repair this by buying a new RCD plug and rewiring it or if you already have an RCD socket adaptor for another appliance, you can just cut of the plug on the pod/ pump and rewire it into a rubber plug and then plug this into the RCD adaptor and the lay z spa should no longer cut out. The RCD is important because you do not want to blow the unit inside.
I hope this helps, If you need more assistance, please ask.

Posted on Jun 12, 2010

  • gallydavid Jun 12, 2010

    Alternatively, there could be something blocking the water flow in the unit which would cause the message to come up and the RCD to cut out, so before you take my earlier advice, i would check for signs of blockage in the unit. If not, then proceed.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Signature Titan II keeps tripping the breaker


check to see if recirculation pump is working if so check to see if heater element is not shorting out

Jul 13, 2014 | Qca Spas Jewel Series Topaz Plus Hot Tub

1 Answer

Layz spa pump 58113 is very noisy can I replace the bearings or get a new part


If you are going to pay someone to replace the bearings, you may aswell pay the money to replace the motor and do a seal change

Mar 11, 2014 | Pool & Spa

1 Answer

Why doesnt my leisure bay spa get hot


This could be caused by a couple things. In order for your spa to heat your pump must be working, your heater and heater sensors must be good. If your heater is bad usually the breaker will trip. If that's not happening read below...
Does water shoot out of the jets when you press the jets 1 button? If not then you have a bad pump or the pump is air locked. The heater can't turn on if the pump does not push water through the heater. You'll know if this is happening because you'll get an error code on your control pad.
So your jets are working but no heat. This is the most common problem. Your spa has a sensor that tells the spa if it's ok to turn the heater on. That sensor is prone to failure so everything can be fine but the heater will not turn on. Get the model number off your spa pack and click the link below. Call and tell them you need a pressure switch and give them the model number. Install the new switch and you're back in action.

http://www.spapartsdepot.com/category/pressure_switches/

Mar 10, 2013 | Pool & Spa

1 Answer

What is error code 6cf on my lay-z-spa


How can i solve this problem?

Jul 27, 2012 | Pool & Spa

1 Answer

I have a Dream Maker Eclipse spa. We just had the pump replaced, but the tub is getting TOO hot that we cannot even get in it. We opened the housing and see 2 metal heat sensors but they are not attached...


The readout may be getting it's temperature from one of those sensors that are hanging in mid-air, not surprisingly low. Both sensors have to be somewhere that they can read some water temp. One of them probably goes into the piping before the heater so it can tell actual water temperature. The other MAY go in piping after the heater in the event of high water temp, it will shut the heater off. Look for a schematic in and around the spa.

Dec 19, 2010 | Dream Maker Spas Dream Maker Ez Spa Hot...

1 Answer

Heater is shaking and making a loud noise when


not enough water flow if filters and pump ok check manual bypass for bad spring if ok see if plumbing bypass it should only be half way open

May 29, 2010 | Raypak Free Hydraulic Lift Gate Delivery -...

22 Answers

Layz spa pump


same problem I had so I seperated the globe by taking out the 5 screws around the middle then removed the nut from the hole the filter sits on its a strange fitting and must have a special key but I improvised by tapping it anticlockwise using a screwdriver and rubber mallet, once open identify the heater unit (it has a single wire going into it and is fastened to a length of metal pipe) and remove it by loosening the clamps at either side and pull the heater free, once free dismantle the plastic casing on the top of the heater inside you will see the live, neutral and earth wires, you can see the live (brown) wire goes to the water flow switch then the temp switch then the heater all I did was bypass the water flow switch by disconnecting the short wire from it going to the heat sensor and replacing it with the brown wire coming from the mains and it works fine now

Jul 15, 2009 | Pool & Spa

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

1,515 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

3543 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...