Question about Panasonic BL-C1 Network Camera

1 Answer

Cameras stopped working after power outage

We have 4 of these cameras & they have slowly 1 by 1 quit working & it always seems to be after a power outage. Would the outage fry the cameras? They are still plugged in but it is like they have no power w/ no lights on or anything. Is there anything we can try to fix them? Or if we buy a new camera & plug into existing set up will that work?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Panasonic Master
  • 2,995 Answers

Sounds like they have been fried by a power surge - it will be worth having surge protection on them in any future installation.
Is there any voltage/hz selection on these units that need adjusting to suit local conditions or do you purchase against a specified voltage / hz ?

Posted on Sep 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shredder has quit working after a power outage.


Sounds like it fried despite the "surge strip". Which is not a proper filter for big surges, just a cheap movistor which might be fried also if you took it apart.

Apr 10, 2017 | The Office Equipment & Supplies

1 Answer

I have wintv-hvr-1950 hauppage box which suddenly stopped showing light. all things are connected as always - computer/internet working fine -Windows 7 - WinTVV7 screen opens black on my monitor


Make sure the power supply is working. Quite often you get a pretty crappy power supply with USB devices, so that is what I would suspect. Its a 5 Volt supply, and should get a little warm if its working. I don\'t think this device will work without a power supply.

Those supplies are quite standard, so bring your old one to Fry\'s, MicroCenter, Radio Shack, Best Buy, or even Walmart or the other stores to compare Volts, Amps, and polarity/size of the plug to make sure you get one that will work.

Sep 26, 2014 | Hauppauge Hauppage WinTV-HVR-1950 USB TV...

1 Answer

Runs but will not heat. Power outages in area over last few weeks.


If the dryer was running during an outage, even with a very brief flash there usually is a power surge when it comes back on. If everything else seems to work okay it's possible that the heating elements got fried. You can check them with a voltmeter. Also check to seek if the dryer has overlaod protection. Most have a reset. One other thing that could happen, the breaker is defective. That you can check at the back of the dryer where the plug cable attaches to the dryer.

Apr 09, 2011 | LG DLE2516 Electric Dryer

1 Answer

After lightning strike & power outage digital display & oven not working. is there a fuse or reset button? or is the circuit board fried?


Start by investigating, open at the point where power cord goes in there is a fuse if it is o.k there is another smaller trans former powering the display board that normally uses thermo fuse, find out whether the thermo fuse is blown i hope this solves your problem

Aug 02, 2010 | Microwave Ovens

1 Answer

1998 Chev. Cavalier's A/C not working & affected power


Possible ac compressor locking up.will drag engine downt till clutch coil fries.

Jun 18, 2009 | 1999 Daewoo Lanos

1 Answer

Cannon printer quit working suddenly.


Is it possible that the cord came unplugged from the transformer itself instead of the printer or wall plug?
A power outage shouldn't affect it, but a power surge can. Please use surge protection circuits on your computer equipment. It's so much cheaper than repairing or replacing them.
Take it from someone who learned the hard way....
You can try a printer reset. Turn the printer off, unplug the power and data cables from the machine. Wait at least ten minutes to allow the printer cache to be purged.(Canon's recommendation)
Then plug back in and turn on.
I hope this works for you! Good luck!

Apr 10, 2009 | Office Equipment & Supplies

1 Answer

Pointer locks up on the desk top after a power outage


Tried a different mouse? Maybe the power outage fried it. pc2 mouse? If it the wirring is fried or the mother board for the mouse is fried then you could purchase a USB mouse if you have an available port.  Finally download the mouse driver and reload it first.   Any more questions please ask. Thanks
http://h10025.www1.hp.com/ewfrf/wc/product?product=472140&lc=en&cc=us&dlc=en〈=en&cc=us

Jan 19, 2009 | HP Compaq Presario SR1500NX (PX786AA) PC...

1 Answer

Camcorder just quit - no power


Hi There, Have you tried plugging in the d/c power cable from your charger? The power supply board inside the camera has 4 fuses, 1 is for the battery power, 1 is for the d/c plug in power, 1 is for both and the 4th is for lens functions. The camera may NOT be completly fried. A good service shop should be able to get your tape out without damaging it and give you an estimate for repair at the same time.
Let me know, mr cicmo.

Dec 28, 2008 | Cameras

3 Answers

Stand by button flashes but receiver wont turn on


I have vsx-d812 that has an AMP ERR in error menu. the troubleshooting was found to be Q696 and Q697 in the DC prot. area on "C" board, up near front toward diplay in center of c board. You can get access to error codes on VSX pioneer unit by pressing "enter" and "adv. surr." simultaneously for 2 sec. The display should show what error code you are experiencing. I believe there are three diff. error codes. 1) AMP ERR 2) OVERLOAD 3) BOAD ERR (not mistyped) I hope this helps pinpoint error code for ya.

Oct 07, 2007 | Pioneer VSX-816-K/S Receiver

Not finding what you are looking for?
Panasonic BL-C1 Network Camera Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Computers & Internet Experts

Oloyede Monsuru

Level 3 Expert

1417 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

micky dee

Level 3 Expert

2995 Answers

Are you a Panasonic Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...