Question about Maytag PAV2300 Top Load Washer

2 Answers

80 Series Kenmoore will not spin or timer move

I have a 80 series Kenmoore and the spin will not work, but the raise and wash will work, do I have to replace anything or do I just go out a purchase a new one.

Posted by on

  • BMac28 Jan 16, 2008

    I also have a Kenmore 80 series, everything seems to work but the spin cycle. The big problem is that the spin cycle seems to be the only time the water drains so it is still full of water. How do I fix it and how do I drain it?

  • William R Whitney Jr Jan 06, 2013

    Kenmore 80 Series will not do anything. Turn timer to all the cycles and nothing happen. The only thing it does is fills with water. What can I do to fix this.

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 222 Answers

Check the lid switch I think the 80 has the little plastic plunger to

push the switch down . Lift the lid and let it down again and listen for a click. If it clicks most likely the sw is ok. You could check the switch with an ohmmeter though to be sure.

a bad lid sw will cause no spin. Do this before buying a timer.

Always check everything else first before replacing the timer.

If it isn\'t agitating or spining check the coupler between the motor and the gear box. Don\'t buy a new washer if you can fix this one it will be better than a new one with all the problems they have. Also yours is built better and stronger. It\'s not that hard on these machines. Good Luck hope this helps. Sorry I didn\'t see the part where the timer wasn\'t moving if it isn\'t it could be the timer. Be sure and check all connections first and check timer motor. Timers are expensive. .

Posted on May 17, 2013

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 80 Answers

The timmer were the knob is attached to has gon bad it very easy to replace 8 screws and one plug part can cost from 40-80 dolllars

Posted on Dec 19, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a Kenmore 80 series top load washer model 110.28803890. When the timer moves to spin it makes a load clicking noise and does nothing.


Timers are not supposed to make loud clicks. If it is, it's going bad. The same problem happened with my parent's Estate washer. It its on it's third timer!

May 24, 2012 | Kenmore Washing Machines

1 Answer

Kenmore 80 series top load washer. In the permanent press mode the machine will stop when it moves to the rinse mode. I can manually move the time past the midpoint of the cycle it will run for a minute...


So it will spin and drain when put in the spin cycle right? More than likely it is your timer if you have to keep manually setting. I would check on timer prices and go from there.

Dec 28, 2010 | Kenmore Washing Machines

1 Answer

I have a series 80 top loader. It filled and


Screws holding the lid switch was broken. Had to replace lid switch.

Jun 11, 2009 | Kenmore 24902 Top Load Washer

1 Answer

Kenmoore 80 series heavy duty (gas dyer) no heat.


If you still need help please post your model number. Gas/Electric?
Eric

May 25, 2009 | Kenmore 63942 Dryer

1 Answer

Kenmore washing machine will not drain


Replace the timer.
This is a neutral drain machine. If there is no natural pause in the timer at the end of the rinse cycle the timer is bad.

Mar 13, 2009 | Kenmore Washing Machines

1 Answer

Kenmore Series 80 Washer timer knob spins


Something in the timer came apart. Timer needs replaced. When in good working order, the timer should ONLY ever be turned clockwise..Reversing this could break it.

Mar 11, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore Series 80 Washer Won't Spin


Your timer has failed to initiate a pause for the transmission to lock in.
Replace your timer. Solve your problem.

Feb 21, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Kenmoore Dryer will not start


ok im with you,,send me the model #..and check your door switch..i want to veiw schematic on this,,,we have a defective part..

Jan 17, 2009 | Kenmore 63942 Dryer

1 Answer

Kenmore series 80 washing machine


This is usally a timer problem that is shorted

Oct 20, 2008 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Maytag PAV2300 Top Load Washer Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...