Question about Sharp AL 1631 Copier

1 Answer

The register says ppppppppp and the register is locked. What do we do?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Sharp Master
  • 1,447 Answers

P means insert paper to casset or single sheet pass tray

Posted on Nov 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door locks do not work


Do they not work from and switch? First, check fuse 5 (30a) which is hot at all times. Then, make sure the drivers door lock has voltage to the black.white wire, if not there is a bad connection between the fuse and black/white wire (the same wire feeds switches on both sides, so find the junction and check from there back to the fuse box). Then check to make sure the other four wires register ground. If the black wires do not, run a new ground to those two wires. If the pink/lt grn-pink/yellow switches do not replace the switch. If you find voltage and ground to the other four wires move to the passenger door switch. both pink/black and pink/orange wires should register ground, and the blk/wht should register voltage. Hold the swirch in one position, one of the ground wires should now register voltage. When the switch is pressed the opposite direction, the voltage should reverse. If you register ground on both sides and voltage but it fails when pressing the switch, replace the switch. If it tests ok, the pink/black=pink/orange wires that feed the locks are losing connection between the locks and switch. You then have to move to the lock closest to you and see which wire does not register. The wires from the passenger switch yo the wire that feeds the locks or the junction where the two meet are bad.

Mar 25, 2010 | 1999 Ford Explorer

1 Answer

How to register .dll in locked PC?


Press F8 every 5 secs during startup and select Safe mode

Logon as administrator and register the dll in there

Feb 09, 2009 | Microsoft Computers & Internet

2 Answers

I purchased a Garmin 200 GPS off ebay, it is locked, I tried registering it on the Garmin website to get the unlock codes but was told the serial number I entered was already registered. I there any other...


Looks like the person who sold you the GPS has already used the unlock code so you should go back to the seller and ask for a refund as it is not possible to get round the unlock code.
Peter

Jan 27, 2009 | GPS

1 Answer

Why does my key fob only open drivers door


this how a dealer does it:
DOOR CONTROL TRANSMITTER
REGISTRATION
1. REGISTRATION OF RECOGNITION CODE
HINT:
 The add mode is used to retain the already registered codes while registering a new recognition code.
This mode is used when adding a transmitter. If the number of the registered codes exceeds 4, the previously
registered code will be correspondingly erased in order, starting from the first registered code.
 The rewrite mode is used to erase all the previously registered codes and register only new recognition
codes. This mode is used when exchanging the transmitter or the door control receiver for new one.
 The prohibition mode is used to erase all the registered codes and cancel the wireless door lock function.
Use this mode when the transmitter is lost.
 The confirmation mode is to confirm how many recognition codes have already been registered before
an additional registration of a recognition code.
 All the following registration procedures must be performed in order continuously.
(a) The vehicle should be in the following conditions.
(1) The key is not inserted in the ignition key cylinder.
(2) Driver’s door is OPENED. (The other doors are CLOSED)
(3) Driver’s door is UNLOCKED.
(b) Perform the following operations to select the desired mode.
(1) Insert and remove the key from the ignition switch twice within 5 seconds.
(2) After the above operations, close and open the driver door twice within 40 seconds. Then insert the
key into the ignition key cylinder and remove it.
(3) After the above operations, close and open the driver door twice within 40 seconds. Then insert the
key into the ignition key cylinder and close the door.
(4) Turn the ignition switch from LOCK to ON and back to LOCK at approximately 1 second interval 1
to 5 times to select a mode.(2 times for rewrite mode) Then remove the key from the ignition key cylinder.
(5) After selecting a mode, the integration relay automatically performs the power door
LOCK-UNLOCK operation within 3 seconds to inform the selected mode.
(c) Register the new recognition codes :
(1) Within 40 seconds after the add mode or the rewrite mode has been selected, press the LOCK and
UNLOCK switches on the transmitter switch simultaneously for 1.0 - 1.5 seconds.
Within 3 seconds after the previous operation, press either one of the switches for more than 1.0
seconds.
(2) Within 3 seconds after the transmitter switch has been turned OFF, the LOCK-UNLOCK operation
will be automatically performed once if the registration of the recognition code of the transmitter is
completed correctly. In case the LOCK-UNLOCK operation is performed twice, the registration of
recognition code has failed. Perform the registration procedure from the beginning once again.
(3) If the multiple transmitter to be registered, repeat step (c) within 40 seconds after the previous registration.
this is why the dealer charges for this

Jun 19, 2008 | 2003 Mini Cooper

Not finding what you are looking for?
Sharp AL 1631 Copier Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

255 Answers

k24674

Level 3 Expert

7993 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...