Question about Sony XL-2100U Projector Lamp for KF-42WE610, KF-50WE610, KF-60WE610, KDF-60XBR950, KDF-70XBR95

1 Answer

The VPL-CS6 turns off after about 4 seconds of turning it on. Any suggestions? I have had it about 6 years...will start using it everyday now due to getting a smart board. Any suggestions other than a new bulb or clean filter?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

You must replaced the lamp ballast of your projector.

Posted on Oct 08, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sony Vpl -cs6 Lamp hour reset Procidure.

Connect the power cord and turn on the projector.
When it's in standby mode, press the following keys on the remote in this order for less than 5 seconds each.
left arrow
right arrow

Aug 20, 2011 | Sony VPL CS6 Multimedia Projector

1 Answer

Projector works for about 20 seconds then starts flashing lamp/cover light

I am having the same problem. Have you ever put this projector in emergency mode by turning the the grey screw on the bottom of the projector? I am looking heavily into this, maybe we can help each other out along the way. (armyvet96 at hotmail dot com)

Oct 30, 2010 | Sony VPL CS6 Multimedia Projector

1 Answer

I have Sony VPL CS6 projector and the lens cover stays open and wont shut to cover the lens!! The Lens/Cover light on it flashes? It does project for about 15seconds or so but then goes off, this is when...

It is possible that there can be few reasons for the fault siad:
1.the lamp can be faulty
2. the filter can be clogged.
3. the lens cap trigger switch can be faulty and staying on
4.The power supply can be faulty, not delivering the power but shuts off.
5,the main processor board can be faulty witth errors.
It might need board swapping to confirm.

Sep 25, 2010 | Sony VPL CS6 Multimedia Projector

1 Answer

Manual de sony svga vpl-c57

I have the CD projector but i can

Jun 14, 2010 | Sony VPL CS6 Multimedia Projector

1 Answer

My Sony Data Projector VPL CS6 is stuck in emergency mode, can it be reversed.

I tried the emergency mode and recovered the powered mode. just make sure you can turn the adjuster ( that big grey plastic screw) freely and leave it that way (don't tighten it or put the **** back in). try turning it on. works for me..

Feb 23, 2010 | Sony VPL CS6 Multimedia Projector

1 Answer

My VPL CS6 will not turn on. I tried different cords and power points and the dust and lamp covers are securely closed.

It could be that you have put the projector into emergency mode. If this is the case you can only switch it on by moving the small switch by the leg tilt underneath, and then maually open the lamp cover by turning the adjuster with a coin, see page 48 of the manual for instructions. Hopw this helps

Jan 24, 2010 | Sony VPL CS6 Multimedia Projector

1 Answer

My projector sony vpl cs6 projects yellow

reset the settings to factory default and change your cable. if that doesn't help, the polarizer filter on the blue lcd panel is fried due to excessive dust and heat. the optical engine will need to be replaced.

Dec 07, 2009 | Sony VPL CS6 Multimedia Projector

2 Answers

Sony VPL CS6 in darkness !

Make sure the interlock switch is activated by the cover of the lamp.
Can't measure a voltage with the lamp cover open. High voltage is powering the lamp from an smps or ballast supply. If lamp is New, cover switch is good, then the lamp power supply could be faulty.


Dec 29, 2007 | Sony VPL CS6 Multimedia Projector

Not finding what you are looking for?
Sony XL-2100U Projector Lamp for KF-42WE610, KF-50WE610, KF-60WE610, KDF-60XBR950, KDF-70XBR95 Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Office Equipment & Supplies Experts

shaun taylor

Level 3 Expert

1527 Answers

Jaime Hernandez

Level 3 Expert

2335 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Sony Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides