Question about Computers & Internet

1 Answer

GE networX security command center keyupad is frozen. I have 2. We replaced the battery that was needed, but before that was done the keypad froze with a shimmering light in the fire zone and a yellow light in the service zone. Our bedroom keypad reset when system was powered down. The other one is frozen. Any suggestions. It won't take any input at all. Should I take it off the wall and try to fix it? Help!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Since you did not list the model I cannot be certain this will help you, however if it is the correct model then there is a service section on page 16 that should help. http://www.elvey.co.za/ProductFiles/d9726436-02b3-48ae-894f-0e03b2e6c072.pdf

Posted on Oct 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am tyring to buy a replacement door bell/intercom. Where can I find them?


Try contacting the security alarm company for assistance. ADT used this system in the past. You may also want to try a local security service to see if they can source the parts for you.

Mar 31, 2015 | GE Networx NX4 Security System

1 Answer

Two fire/smoke sectors occasionally beeping - no battery inside - connected to NetworX 1448E security system. We have changed the large battery in security - still beeping


If the units are more than 5 to 7 years old they have reached the end of life cycle and need to be replace. Smoke detector typically are only good for 5 to 10 years.

Sep 04, 2014 | Home Security

1 Answer

Installation manual


need to install nerf bars on jeep wrangler 92 have part #b07s0906

Jan 03, 2014 | GE Caddx Networx Fixed English LCD Keypad ...

2 Answers

Keypad message reading 12volt low battery on three wireless zones. changed out all batteriies and still getting message.


This could be referring to your battery backup for the control panel. Make sure your battery connections are secure and check the batteries' voltage with a multimeter. If it is showing less than 12 volts and has been connected to the control panel for more than 24 hours, the battery is bad and needs replacement. Contact your local alarm company and ask them verify the battery is bad, and they can install a new one for you right then.

Feb 23, 2011 | GE / Caddx Networx NX 8 Control Panel...

1 Answer

Can I adjust the volume on my GE Networx NX-148E keypad?


There are a couple of things you can do, you can silence the keypad via a programming change to the alarm panel, but this requires knowing the installer or 'go' code. On the other hand, you can change the tone of the keypad by pressing * 0 and using the arrow keys to adjust the tone up and down.

Feb 10, 2011 | GE / Caddx Networx Programmable LCD Keypad...

1 Answer

Hi, i'm using the Caddx NX4V2, the fire light flashes rapidly and no keys are working to stop it, i did read a manual that says the rapid flashing fire led means that there are problems ... how do i pin...


If you know the 'go' code ( default 9713 ), you can press *+90 to see the event log, which you scroll through with the arrow keys on the keypad (alpha keypads only). If that is not available, you will need to have a certified alarm installer come and check your system for faults.

Dec 13, 2010 | GE Iti Caddx Nx4 Control Panel 48 Zone...

1 Answer

Hi Liam here I just installed a networx nx4 and when powered up key pad has 1,2,3,4 flashing rapidly with service light on I was able to get rid of service light but zones still flashing And there is only...


This could be a supervision problem. If zone expanders, gsms, keypads, etc. are added to this alarm panel, you must enroll the device with the control panel. This is done by entering into programming mode ( * + 8 + {go code} ) and then simply exiting programming mode by hitting the exit button. The GE NetworX control panel and it's affiliated compatible devices will auto-enroll after about 15 seconds. The default 'go' code is 9713, but this is usually changed by the alarm company installer.

Apr 21, 2010 | General Electric GE NX-591E-GSM NetworX...

1 Answer

GARMIN STREET PILOT 320


To unlock a “frozen unit,
1. power it off
2. Remove the face plate, Gently pry on the face plane. In the center top edge (under the Garmin logo) you’ll see a small notch.
3. on the right side of the unit, press the reset button.
4. replace the face plate
5. Power it back up.
The unit should restart normally.

Mar 21, 2008 | GPS

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

1,371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...