Question about Konica Minolta bizhub C450P Laser Printer

1 Answer

Malfunction C-11A4

Our machine won't do anything! And our "oncall" tech cannot come until Friday!

Is this something I can fix?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers
Re: Malfunction C-11A4

Its a finisher exit motor error, maybe you had a paper jam in which case try opening the front cover of the copier(where the toner cartridges are) and close again to clear the code, or switch off the machine and back on again. Good Luck

Posted on Aug 07, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Error c-11a4

Subject C-11A4 code occurs after updating the flash ROMCause: The Flash card to update the firmware was applied to the wrong board
found on kmbs site ssd

Jul 31, 2013 | Konica Minolta Minolta Di450 Di470 Di550...

1 Answer

How to fix C-0500 error for BIZHUB C350 konica minolta printer

Open the front door with the machine on, get down on the floor and look up on the right side of open area there is a slanted section in that slated section is a small hole you will not see it standing! With a small screwdrive gentle push the small switch located in side the hole that will reset the code if it comes back DO NOT RESET the copier is telling you something is wrong with the FUSER UNIT the HOT part continued reset might catch the machine on fire and that would ruin a perfectly good day. Have a qualified Tech look at it from Konica Minolta.Check this web site out for a rough idea of cost to replace the fuser.

Precision Roller Printer Toner Cartridges Parts and Supplies Office...

Jan 31, 2012 | Minolta Printers & Copiers

1 Answer

We have a Konica Minolta Di2010 - we are getting a message on the screen that read: "A malfunction was detected. Please call your tech rep with this code: C0920" What can I do to get the...

C0920 as per the Minolta Factory Service manual is caused by a tray 1 lift motor failure. In my experience with this code, it is usually caused by paper loading in the tray or something jamming the tray. Best solution is to remove all paper from the tray. Leave the tray open an inch or 2 and turn the main power switch off then back on. The main power is on the back of the machine NOT the one on the right edge of the operation panel. Once the code has been cleared then try a test copy by using one of the remaining trays. If it works correctly then re supply paper into the top tray 1 and then see if the code returns. If it does then either your lift motor is bad or you have something jamming up the lift plate in the paper tray. You can always leave that tray open and run the machine until you can get someone out to look at it. Most of the time tho, reloading the paper in the tray will solve the code.
Good Luck and Thank You for using Fixya

Dec 16, 2010 | Konica Minolta Printers & Copiers

1 Answer

Clean Unable 46 how pleaes brother dcp130c


The message "Unable to Clean. " will appear on the display if there is a
mechanical malfunction of the Brother machine OR a foreign object, such as a paperclip or ripped piece of paper is stuck in the

First, check the machine for any foreign objects:

1. Open the scanner cover by pulling up on the lower right corner of the
cover until it locks into place. Look inside the Brother machine and remove any foreign objects.

2. Close the scanner cover by lifting it slightly to release the lock,
gently push the scanner cover support located in the back of the unit
and then close the scanner cover.

3. If the error message continues to appear on the display the machine
will need to be reset. To reset the unit unplug the Brother machine
from the power outlet for several minutes and then plug it back in.

If the message continues to appear on the display and your machine is
within warranty, you can locate a Brother Authorized Service Center
(ASC) in your area by clicking on the link below: or contact Brother
Customer Service by calling 1-877-Brother (1-877-276-8437) Monday
through Friday, excluding holidays.

If your machine is out of warranty, you can locate a Brother Authorized
Service Center using the information listed above.

Please Let me know if this works, or if it does not.

Ryan Frame
Creative Energy Associates Technical Center

Aug 02, 2009 | Brother Printers & Copiers

1 Answer

Hi there!!! My printer displays error message: malfunction detected call representative - c3751. Kind regards

hi this is a high temp code, you need to replace the fixing unit then get a service tech to reset the machine

Jun 05, 2009 | Konica Minolta bizhub C250 All-In-One...

1 Answer

Fax Reserved

try unpluging the machine and the replug and let the machine reboot. brother tech

Jan 07, 2009 | Brother MFC-8440 All-In-One Laser Printer

1 Answer

Brother MFC 3100 Printer/fax

This is the only reference I could find on error 41: How can I clear the message Machine Error 41 from the display? (ME41)

Machine Error 41 indicates a mechanical malfunction of the Brother
machine. Unplug the unit from the power source and then plug it back

If the error message continues to be displayed on the LCD, please call
Brother Customer Service at 1-800-284-4329 for assistance. The Customer
Service center is open Monday through Friday, from 9:00AM to 7:00PM,
excluding holidays If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Oct 16, 2008 | Printers & Copiers

3 Answers

Minolta Dialta620 copier error code c-0000

Code C0000 if a fuser motor failure.

Check to see if anything is damaged in the fuser (the thing that gets hot).

Also, check for a jammed transparency (if you use them).

Feb 10, 2008 | Minolta DiALTA Di620 All-In-One Laser...

2 Answers

My brother mfc 210c won,t scan or copy

I just called Brothers product support and found out that these machines WILL NOT scan or copy or do anything until the ink cartridges have been replaced. So there is no other solution.

Nov 26, 2007 | Brother MFC-5840CN All-In-One InkJet...

Not finding what you are looking for?
Konica Minolta bizhub C450P Laser Printer Logo

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Printers & Copiers Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

5693 Answers

David Burkhart
David Burkhart

Level 2 Expert

207 Answers

George Mclaughlin

Level 2 Expert

330 Answers

Are you a Konica Minolta Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides