Question about Samsung CXD1334 13 in. Combo

1 Answer

"Factory" on display

My Samsung CXD1334 shows the word "Factory" in red letters continuously on the screen. I cannot find a factory reset or any other way to clear the word off of the screen.

How do I get rid of the display?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: "Factory" on display - Samsung CXD1334 13 in. Combo Combination Televisions

Lets just buy her a new one. blv

Posted on Dec 26, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Tv won't come on.

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Jul 18, 2016 | Coby Combination Televisions

1 Answer

Samsung LCD TV LE40R8 - Hard Reset

How do I reset the picture on my LCD TV to the factory settings?
The P.Mode button on the remote of your LCD TV lets you cycle through four factory preset picture modes: Dynamic, Standard, Movie, and Custom. To return the picture on your TV to the original factory preset, press the P.Mode button on your remote until the TV displays the Standard mode.

Nov 14, 2007 | Combination Televisions

1 Answer

Convergence Adjustment Pattern

This was for a similar model.

In convergence mode press 1 for no compensation, 2 for factory default and 3 for last saved setting.


Hope thats it!

Oct 13, 2007 | Samsung HC-P4363W 43 in. TV/DVD Combo

1 Answer

Envizen MaxMade V100MD android tablet got stuck on the android

Plug in the tablet & turn on the device and keep holding down the volume down button to enter the screen that allows you to factory reset the device as the device boots up. The screen should change from the Envision text to black and then the debugging menu. If it shows the android screen name start the process over.
It happened to my V100MD and it worked. Many experts were saying you may have to send it back to the manufacturer or use the volume up approach. Follow the instructions above and it should work.

Jan 25, 2014 | Envizen Portable TV/DVD Combo Swivel9in...

1 Answer

How to disable the msg FACTORY A05A06-01-V08.05 is displayed in TV. pls solve it.

How to disable the msg FACTORY A05A06-01-V08.05 is displayed in TV. pls solve it.

Sep 17, 2012 | Combination Televisions

1 Answer

Panasonic PV-DR2714 will not turn on and i lost the remote

Hello Bobby
You haven't given enough details about the fault to your Combo. What do you mean my 'power button has coninuity on board'. I assumes that you get power LED at the front of your device lights up when you switch ON the main power switch, and the unit refuses to power ON and work further. If so, just make a factory reset to this set as it will reset the memory IC. To reset the unit to its factory reset do the folloing. But to do this, the power LED on the front panel of the unit should light up. Otherwise, the fault will be to its power regulator section. To reset the unit to factory reset:
[1] Turn the Power ON.
[2] Hold down both PLAY/REPET and FF on the unit more than 5 seconds. The power will shut OFF. Please ignore "NO CASETTE" warning.
[3] Perform initial set up refering to its user manual. You can see instructions to initial setup at page [16] of the user manual to your device. OK.

Dec 07, 2011 | Panasonic PV-DR2714 27 in. TV/VCR/DVR...

1 Answer

My Samsung HC-p4363w have no pic or sound but the power red light is on

Try pushing the "source" button on remote or on the TV. Wait about 5 seconds, if no picture, push again. Do this at least 6 times or until you get a picture. With each push, the TV will look for cable input, dvd input, etc. until it finds your cable signal.

Also make sure your cable/antenna is hooked up and working.

If that doesn't work, hold down the "enter" button for 10 seconds to reset the tv to original factory settings. Then follow the on-screen menu setup instructions.

-please rate me. Thanks and good luck.

Nov 20, 2009 | Samsung HC-P4363W 43 in. TV/DVD Combo

1 Answer

Samsung HC-P4363W turning off

Not a cooling problem. Power supply voltages are changing from the factory requirements...accordianman

Jan 14, 2008 | Samsung HC-P4363W 43 in. TV/DVD Combo

Not finding what you are looking for?
Samsung CXD1334 13 in. Combo Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Combination Televisions Experts

The Knight
The Knight

Level 3 Expert

66413 Answers

sonic boom...
sonic boom...

Level 3 Expert

1557 Answers

Steven Wander
Steven Wander

Level 3 Expert

574 Answers

Are you a Samsung Combination Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides