Question about Logitech Harmony 659 LCD Remote Control

1 Answer

Stuck in safe mode, what do I do. I changed the batteries and it says safe mode, no lights no anything. can you help?

Posted by on


1 Answer

Update the firmware.

1. In the software, click "Downloads"
2. Click on "Firmware."
3. Update the remote

That should fix it!

Posted on Mar 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need help on how to disable safe mode box on my cell phone screen

If your phone is STUCK in Safe Mode though and restarting it or pulling the battery doesn't seem to help at all then it could be a hardware issue like a problematic volume key (key might be stuck)

Jun 29, 2017 | Cell Phones

1 Answer

Dell demention 3000 stuck in safe mode changed with new battery reconnected all connections holding on the on buttons for 10 seconds but nothing works can anyone help.

If it stuck in safe mode, then it may be a software issue. Re-install the operating system because the fact that you were able to access safe mode means that it is just a software issue.

Sep 07, 2011 | Dell Dimension 3000 PC Desktop

1 Answer

Logitech Harmony 550 stuck on Safe Mode --Have Changed the batteries and checked that they are in correct--However, unable to access anything with remote including the Help button.

Hi everyone. So I can see that there are a lot of people who are having trouble with their Harmony remotes being stuck in safe mode. Here's how to fix it and get your remote working again:

1. Connect your remote to the computer.

2. Launch the Harmony Remote Software, and log in.

3. Click "Downloads" at the top and click "Firmware"

4. The remote will go through the firmware update.

5. Select "Yes", and click NEXT to update the remote.

Voila! Hope this can help

Nov 24, 2009 | Logitech Harmony 550 Remote Control

1 Answer

My Logitech Remote 550 is Locked in the Safe Mode. How do I get it our of Safe Mode.

Doing a firmware upgrade is the BEST way to recover from Safe Mode. A remote may go into safe mode itself for a variety of reasons.

However, if the remote fails to communicate with the PC when it is stuck in Safe Mode, please try the following.

1. Remove the batteries from the remote & check for any stuck buttons especially the Power button that may be causing the remote to stay in this state.
2. If it still will not apply firmware to get out of safe mode, then still without batteries hold down the #2 button while plugging into USB, and it should exit Safe Mode, and say something similar to 'Firmware Upgrade Success'. Even though it says this, still perform the Firmware upgrade since it was stuck in Safe Mode to begin with.

Hope this helps

Sep 24, 2009 | Logitech Harmony 550 Remote Control

2 Answers

My Harmony 890 is blinking and won't do anything!!

try doing a firmware upgrade after booting your remote in safe mode

Jun 03, 2009 | Logitech Harmony 890 LCD Remote Control

2 Answers

Safe mode!

I can help you with your Harmony One Remote Control.

Replacing the firmware in your Harmony One is the way to get it out of Safe Mode.

To help you make sure the firmware update is successful:

  1. May I suggest you make sure you are running the latest Harmony Setup Software (V 7.7.0).
  2. Replace your remote's batteries with fresh ones. It is important the remote has sufficient, unvarying power when updating firmware.
I hope that helps.
Harmony One Manual Download
Logitech Harmony Firmware Update
Harmony Win Software Download
Logitech Harmony Safe Mode Fix
Harmony Remote Glow Light Fix

Apr 18, 2009 | Logitech Harmony One Advanced Universal...

1 Answer

Safe mode keeps appearing on my desktop

This may sound stupid but your F8 key may be stuck. Has anything been spilled on your keyboard?

Jan 31, 2009 | Computers & Internet

8 Answers

Safe mode

To get your 550 out of safe mode, follow these steps.
1. Remove the batteries.
2. Hold the '2' button down.
3. While still holding the '2' button down, replace the batteries.
4. The remote will boot into the normal functionality.

Note: If the 'Off' button is held down while inserting the batteries, the remote will boot into 'Safe Mode'.

Sep 29, 2007 | Logitech Harmony 550 Remote Control

Not finding what you are looking for?
Logitech Harmony 659 LCD Remote Control Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Logitech Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74634 Answers

Jerry Umali

Level 3 Expert

979 Answers


Level 3 Expert

1162 Answers

Are you a Logitech Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides