Ihave a blinking black ink indicator light. I have a flashing light on my display ;

Did you refill the cartridge? If so, then you will need to reset a chip on the cartridge somehow. Usually epson doesn't sell "refill" ink unless it is an EcoTank series printer.

These blinks (flashes) are fault indication. By the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit stage inside the TV. Count the blinks occur at one time switch ON, carefully. Do it once again, and make sure about the number of blinks. If the flashes are continious, non-stop, the main system control IC should be suspected. If you wish to get more details, check the site linked here. It has blinking codes detail to many brand TVs. Pull up older posts. Check the site in 'Mosaic' view. It will make search easy. http://electronicshelponline.blogspot.com/

That is an indication of regular functionality from device. Red on device is indication of power on cables ready to capture prints. Usually with devices that has several lightening indication displays, a yellow would be ready to produce print request where finally green is indication that print asignment has been attained succesfully. once a new ink was installed, attempt to print documents to ascertain the status to devcies.

hello,


All error codes start with the letter "E". An error code of E11 will have the five indicator lights flash once and the Start indicator light flash once.


Some models of Frigidaire washers come with a digital readout display that informs the operator of the unit's function and any errors.

Error codes indicate that a problem has occurred and should be addressed. Different models of Frigidaire washers may vary in their fault displays.

Some washer models use flashing lights at the unit's start, door lock, wash, rinse, final spin and control indicators to display error codes.



If the five indica

tor lights flash more than nine times, this signals a letter in the error code. The letter "A" stands for 10 flashes, "B" for 11, "C" for 12, "D" for 13, "E" for 14 and "F" for 15 flashes. An error code of EB2 will have the five indicator lights flash or blink 11 times, and the Start indicator light blink twice

hope this help?

thanks.

E2 mean reload the paper correctly and press Black or Color key from panel board.

Customer Support SUPPORT"; //--> Print | Email | --> Link KnowledgeBase Product
Product
--> Lexmark Z615 Country / Region:
Country / Region:
--> United States Language:
--> Language:
English Need to download
a driver? --> Save my information--> Lights Flashing on the Lexmark Z815/ Z816 Color Jetprinter ID: ENUS17112 This document does not apply directly to your Lexmark Z615

1. First count the number of times the light on the front of your printer flashes.
2. Then refer to the table below for information about the error condition and recommended recovery procedures.
   
   Number of Flashes Error Condition Error Recovery 2 Carrier Stall:
   The movement of the print cartridge carrier has been obstructed. Remove any objects blocking the carrier path.
   4 Print Incomplete:
   The print cartridge carrier stopped in the middle of a print job due to obstruction. Remove any objects blocking the carrier path.
   12 Cartridge Short:
   The printer has detected a short circuit in a cartridge.
   1. Turn the printer off.
   2. Open the front cover.
   3. Turn the printer back on.
   4. Remove the color cartridge.
   5. Close the cover. If there are no flashing lights, the color cartridge is short-circuited.
   6. Remove the black cartridge and then reinsert the color cartridge.
   7. If there is no error indicated by flashing lights, the black cartridge is short-circuited.
   8. If you continue to receive an error indicated by flashing lights, both cartridges are short-circuited.

problem here is the orange light blinking- has ink in the cartridge- stopped printing in the middle of the page

not sure w/ this one, but is it blinking too fast on printer, the check color and black ink cartridges? and if yes what is the color of the light, is it yellow or red, and is the on and off lights, flashing?
-black and color blinking fast - install printhead
-black and color blinking slow - no cartridges installed
-on and off blinking black and color steady lights, calibrate

-hope this helps, or else contact kodak
-xoxo

Red flashing light on '8BK' small black cartridge on left hand side.
If this indicates 'low ink' then it is not alerting me on the monitor. I think this is something different because my printing has been interrupted. Aileen

Hi Greenhorn, Your info is slightly conflicting - I think. As I remember the C60 has just 2 LED's: 1 - Green for Power 2 - Red for Error The third button - Cartridge exchange - has no LED Now it is a while since I looked at a C60 and my brain leaks like a sieve, but that's the way I remember it and feel free to correct me if I'm wrong. The error codes I remember are: Printer status - Indicators - Priority Power - Error Power ON condition On - Ink sequence Blink - Ink Cartridge change mode Blink - Data processing Blink - Paper Out *1 - On Paper jam condition *1 - On Ink end (Black) *1 - On -> Blink Ink level low (Black) - Blink-> Blink Ink end (Color) *1 - On -> Blink2 Ink level low (Color) - Blink-> Blink2 Ink end (Black and Color) - On -> On No Ink Cartridge (Black or Color) *1 - On Maintenance request (Ink Overflow Countererror) *1 Alt Blink Alt Blink Fatal error *1 Off On Special setting Blink2 Blink2