Question about Ovens

1 Answer

Zanussi built-in oven ZDF 866W socket blows when turned on

Zanussi built-in oven ZDF 866W When you turn on the top (large) oven the main fuse for sockets blows.
I can use the bottom oven ok & the fan (in top oven) works ok.
Any ideas?
Regards
Bob Waller
rwaller48@hotmail.com

Posted by on

  • Anonymous Mar 21, 2014

    slot in oven

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 42 Answers

Sounds as if a wire to the fsd is shorting when oven turned on.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Top oven fan wont turn off unless I turn the cooker off at the mains


Cooling fan has the function to protect kitchen furniture from excessive temperature. The fan will cool the oven even you turn it off (not unplug from wall socket). This will happen only after the temperature decreasing below 70 degrees. If this does not happen then is faulty thermal cut-out which is located between wiring on the top and has 4 pins.

Dado

Sep 19, 2014 | Zanussi Ovens

1 Answer

Oven light blew and now no power to the oven.


If you are not knowledgable in electricity, call for service.
This is an electrical short at the light, I have seen this before.
The wiring for the light has grounded to the oven. This causes the main fuse to blow. You will need to fix the short first. Then reset the main fuse/replace.
In the case of the wall oven, you may have to remove the oven to fix it properly. Depending on the model and where the short is.

Nov 25, 2013 | Zanussi ZBF360 Electric Single Oven

1 Answer

Zanussi oven zbf 360 + bulb blows repeatedly


bulbs blow from incorrect voltage in use or loose ground wires ( arcing out)
if they fail while the oven is on it is because the bulb construction glass is wrong
bulbs used in ovens need a special heated treated glass and are generally only available from the service agent
failing immediately on turning on indicates a bigger problem that the bulb so call in an electrician to test the system

Mar 24, 2017 | Zanussi ZBF360 Electric Single Oven

1 Answer

The grill on Zanussi FM9232 keeps blowing the main fuse


the grill element needs replaceing or you have a wire on the grill element thats come off and touching down to earth

Sep 07, 2011 | Zanussi ZHQ575 Electric Double Oven

2 Answers

Hi my zbf260w built in fan assisted oven is not getting heat in the oven department.The fan and grill are both fine but not the oven,


If the fan is working o/k, then y ou need to replace the oven element, located at the rear of the oven compartment behind removeable cover.

Sep 26, 2010 | Zanussi Ovens

2 Answers

Zaunssi ZBF360X built in Oven Not Heating


This tutorial will show you how to check your Zanussi element and how to replace your Zanussi cooker element.
Here are the 3 main faults to look for in your oven or cooker that is not heating
  1. Your oven will not work until the clock/timer has been re-set after replacing an oven element or tripping the electrical supply. Consult your Zanussi manual.
  2. If you're Oven is not getting hot or heating up it could be a faulty element, if the fan in the oven is running and the thermostat light is on, this will lead us to believe that the element has gone faulty. With grills the thermostat light should come on there should be heat, if not then this could be the grill element or the thermostat.
  3. When you turn the oven on, the household electrical supply trips on the Rcd (this is the earth trip in the fuse board sometimes called the breaker tripping) your fan oven element has gone to earth and needs replacing.
If this helped like us on facebook please

How to Video Tutorials on Domestic Appliances

Mar 30, 2010 | Zanussi ZBF360X Electric Single Oven

1 Answer

Zanussi Oven inside glass problem


Hi , i removed the door, and removed two small screws from the bottom of the door,you can the seperate the door into two pieces by slidng them apart,cleaned up the glass,bought a tube of heat resistant silicone and put some around the edges of the door and glass. I then replaced the glass,i left overnight to set and rebuilt the door.

Regards

Eddie

Jan 27, 2009 | Ovens

2 Answers

How to remove a fan/motor from a Zanussi oven


You are probably trying to undo the nut the wrong way.
It is a left hand thread, so to undo it, you go clockwise, as though you were trying to tighten it, and vice versa to tighten it up again. If you can't unscrew the nut, you will have to grip the fan spindle with something whilst you undo the nut.
Plz rate my solution.
Thanks.

Jan 22, 2009 | Zanussi ZHQ575 Electric Double Oven

2 Answers

ZANUSSI ZDQ 595 BUILT IN ELECTRIC DOUBLE OVEN


have you reset the clock after the power outage?
this is necessary before oven will work
suspect you have it on auto in error

Sep 30, 2008 | Zanussi ZHQ575 Electric Double Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

ashburton

Level 3 Expert

417 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...