Question about RCA D52W20 52" Rear Projection HDTV-Ready Television

3 Answers

Tv will not turn on

I press the on button and lite just blinks

Posted by on

  • 15 more comments 
  • michelleb Dec 24, 2007

    when i push the button to turn my tv on it blinks 3 times then shuts off.it will not turn on.

  • Anonymous Jan 01, 2008

    the power buton blinks red and gren and it dos"t turn on. What can i do

  • SkipH Jan 03, 2008

    I have Toshiba 43HX71 rear projection TV. It was turned on and all appeared normal when the picture disappeared and power light began blinking continuously. The TV can not shut down (i.e. to stop the blinking) using the power button, but must be unplugged.



    This is the second time this has occurred. The first time, about 2 months ago, I was able to get it working again by unplugging the TV and all inputs from the rear panel, then plugging the TV in again, testing to see that it could be powered back on without resuming the blinking, and finally re-connecting all the input sources. The same process is not working this time.



    Does anyone know what causes this and how much it will cost to fix before I spend the $$ to have a tech tell me to junk it?

  • Anonymous Jan 05, 2008

    Greeb light flashes and the red light is on...... Wont turn on???


  • Anonymous Feb 28, 2008

    the tv won't turn on. The light around the power button flashes several times; then stops. tv never turns on.

    The picture looked like an over-exposed photo. I turned off the tv and can't the tv to turn on.

    I've unplugged the unit from the wall socket, waited two hours and replugged. No result.

  • biso Mar 15, 2008

    I can not get my tv to turn on. The green light blinks 3 times then nothing.

  • marisa0918 Mar 25, 2008

    My Tv does the same thing. When I try to turn it on the red light blinks and the tv "churps" at me. Anyone know what that churping noise is?

  • DTVMAN66 Apr 06, 2008

    I press the power button and the green light blinks three times and then....nothing. I need help!!

  • Anonymous May 12, 2008

    tv will not turn on. red like blinks.

  • ppeak24 May 23, 2008

    Try to turn on my Rca D52w20 It blinks 3 times like its trying to turn on and then shuts off the first couple of times it sizzles it sat for a couple of weeks and I tried it again it work all day then at night it sizzled and shut off, is it the regulaor box if so how is it to box on this TV? ,,,,Thanks for any help!

  • cristj Jul 01, 2008

    The TV just cut off. When I tried to turn it back on the green light came on then off. Then it blinked 3 times. Do I need a new TV

  • Anonymous Oct 07, 2008

    we have the same problem. one day it went off. the power button won't turn on to red, it flashes to yellow and then goes blank. no sound , no picture. nothing.

  • Edward2768 Oct 14, 2008

    will not turn on, when power button is pressed light blinks 3 times and occasionally it will turn on after several tries.

  • Cee-lo Dec 27, 2008

    I have a RCA D52W20 52 Inch projection tv and it will not turn on. The power button flashes on and off 3 times and I here a clicking noise when it flashes but it will not turn on. PLEASE HELP!!! THANKS IN ADVANCE!!!!

  • miller401 Dec 27, 2008

    I have the same problem. Replaced the flyback and the three problem prone capacitors, and still doing the same thing. 3 blinks and the micro processor shuts the tv off??????????????? Paid alot for this t.v. Throwing in the dump, no more rca products for me.

  • benandcandy Dec 28, 2008

    Light blinks and turns off

  • miller401 Dec 30, 2008

    My local radio shack only has huge capacitors (with the same rating) in comparison to the ones that rca used.  Will this make a differace?  Thanks

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • RCA Master
  • 5,138 Answers

Look on Deflection board 3 capacitors need replacing cp150---cp114----cp120 one is 2200uf 16v Two of them are 220uf 35v. Buy capacitors at Radio SHack. If cp150 is puffed up on top it is bad so replace other 2 caps as well.

Posted on Dec 30, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a RCA projection tv and it will not turn on the power button flashes 3 times and I here a clicking noise when it flashes
jim

Posted on Oct 30, 2008

Ad

Where is the ******* answers?

Posted on Oct 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My samsung plasma hdtv willnot turn on the red lite blinks steadily but the tv won't turn on i've only had this tv for 2yrs.


Try pluggng in an additional source (PC, HDMI, DVD player). When you power it on press the source button to see if one switches on. If it does work, pull up the menu and change your input options.

Mar 12, 2011 | Televison & Video

1 Answer

How do you tune Sky+ remote into Sony KDL46W5710 Television


The Sky+ remote should automatically default to Sony TV's. Leave the batteries out for a few minutes and try again. The Code for Sony is 0000.
Or try this :-

With TV and sky box on.
Press the 'TV' button on the remote.
Hold down the 'select' and the 'red' button (of the four coloured buttons) together, until the red light on the remote blinks twice. (takes 2 seconds)
Press the 'TV' button again.
Now enter four zeros, the red light on the remote should blink twice.
Press the 'standby' button (top right).
If the TV turns off, then press 'select' and the light should blink twice again, job done.

If the TV does not turn off then press 'TV' followed by 'standby' again.
Alternate pressing 'TV' 'Standby' until the TV turns off.
When it does, finish by pressing 'Select.
Check the red light on the remote, if it blinks 3 times, then it has run out of options for 0000.


Dec 19, 2009 | Televison & Video

1 Answer

I have the radion shack hdtv remote. Cat no


Download the manual and codes from here

http://www.remotecentral.com/cgi-bin/files/dl.cgi?file=others/radio_shack/15135-manual.zip&area=other

Here is how to set the code...

1. Turn TV on
2. Press TV button on remote
3. Hold P button on remote until LED blinks twice
4. Enter the first 5 digit code for Magnavox TV's
5. Press Power button - TV should turn off. If TV doesn't turn off repeat steps 2-5 with the next 5 digit code, until either TV goes off or run out of codes.
6. If out of codes use searching for code method below...

TV codes for Magnavox

10047, 11454, 10054, 10154, 10000, 10250, 10051, 10180, 10060, 10030, 10171, 10092, 10706, 11913, 11904, 11755, 10019, 11365, 11254, 10802, 10386, 10282, 10020, 10187, 10186, 10024, 10179, 10096

Searching for code

1. Turn on TV.
2. Press TV button on remote
3. Press and hold P button until LED blinks twice
4. Enter code 991 on remote - LED blinks twice
5. Press 1 - Device key blinks twice
6. Press Power button once
7. Press and release CH+ key until TV turns off.

At this point in the manual, the manual is only correct depending on what type of TV you have.

In the manual if you press the Power on button the TV should turn itself back on, the fail to state that not all TV's turn on by the power button, the majority now are triggered to turn on, on channel change, however you can't use channel change here to check it as you'll go to the next code... here is my solution...

8. Turn TV back on either using original TV remote, or buttons on front (most TV's if you change channels they come back out of standby mode, very few now turn on by pressing the power button).

9. Press Power button on remote - TV should turn itself off again.
10. Press P button on remote to lock in that code.

If the device does not turn off press CH- to go back through the codes, press and release P button when TV turns off.

Finding code

If you used the search function you might want to know what code it's using. To do this follow these instructions...

1. Press TV button
2. Press and hold P until LED blinks twice
3. Enter 990 and LED blinks twice
4. Press 1 and count number of times LED blinks this is the first digit of your code (e.g. 1 blink = 1, 2 blinks = 2, etc).
5. Repeat step 4 pressing buttons 2 - 5 for the other digits (e.g. for the second digit press 2 count number of blinks.. etc)

At this point the manual doesn't tell you how to get out of this mode, I presume pressing any other button on the remote other than 1-5 will take you out of this mode, either that or leaving the remote alone for 5 minutes.

Nov 08, 2009 | Radio Shack (15-2147) Remote Control

1 Answer

I need instructions for the zenith universal remote 3201 for a new Panasonic LCD TV


If you have a manual for remote and you try all codes for your model and it didn't work, you may try for automatic search. First turn on TV, and point the remote toward the TV. You press: SETUP and hold, and press button for device: TV, lite is on, then you release all button and press again SETUP, just once, the lite is blinking, now press the power button on a few seconds. When your tv is turned off, you press button TV. Press button for power and it will turn on your tv. Try other commands on your remote, if everything is working that's it, if not do procedure again. Hope this was helpful, if not, ask more. By!!!

Nov 03, 2009 | Zenith ZN-501S Remote Control

1 Answer

My printer is blinking orange lite


Hi there ok try
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal



Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jun 18, 2009 | Canon S400 InkJet Printer

1 Answer

Disney DTD 363-Car 13" tv/dvd


I have xfinity Comcast cable connected to my Disney's CARS TV/DVD combo. I did not have a remote for it because I bought it at yard sale without it. I used Comcast's remote control. I followed their "Searching For Your Code" instructions. #1-turn on your TV. #2-hold SET till red lite blinks twice. #3- enter 9-9-1. The red lite blinks twice. #4-press nd release the CH+ key until TV turns off. #5-once it turns off press SET key nd red lite will blink twice. #6-Now u have locked in ur code. Press power and TV should turn on. Then CH+,CH-,VOL+, and VOL- should work for ur TV.

Apr 16, 2009 | Disney DTD1363-CAR 13" TV/DVD

1 Answer

Where do i find the codes to program my remote to the cable box


you can do a auto progrom

first you turn tv on


on the cable remote you have the io button and the tv button you press them both down at the same time for 3 secounds the io button will light up while it is lite you press the channel button up or down till the tv turns off then you press tv again it should blink twice to confirm the code then you will be able to use the remote with your tv if it dosent work take your time when it goes off dont hit the channel button to fast or again or you will load the next code if it dosent work try it again slowly till the tv turns off

Dec 14, 2008 | Polaroid PLA-4250A 42 in. HDTV-Ready...

6 Answers

RadioShack Universal Remote (Cat. 15-2147) - to use with JVC TV


programming a device: make sure batteries are installed correctly. Turn device on(for ex., your TV). Press TV button next to Power button on your 15-2147...Press and hold the little P button until the red LED lite blinks twice...enter the first four-digit code for your device(in your case,JVC TV...first set of #s is '0463' ) note: the LED will blink once as each number is entered. If the number is correct the LED will blink 2x. Note if the LED doesn't blink twice after entering the 4 digit code, begin again with the next set of numbers. For JVC the codes are 0463 and 0053. Once your remote blinks twice after entering in your TV code, press the power button. This should turn off your TV. Just use like any other remote. Hope this helps you.

Oct 11, 2008 | Radio Shack (15-2147) Remote Control

1 Answer

Remote control code for Emerson LC200EM8


Have you tried the searching for your code option on the 15-2147?
for example, turn on your Emerson LC200EM8( press the appropriate key on your remote, if this is a TV.#1.press the tv key on your remote)..#2.Press and hold the little 'p' key till the LED lite,on the remote, blinks twice..#3..then enter 9 9 1.(the led should blink twice).#4.Aim and..Press the Power off on the remote....(the remote will start sending IR codes from its library to the selected device, starting with the most popular.)#5..If the TV responds go to step 6..if not, press the CH+ button, until it does...step #6 when device responds, to lock in the code, press 'p' once, the LED blinks twice.
Once you have your number locked in,,,you can get the remote to tell you what sequence the code is in by #1Press the appropriate key on the remote.(i.e, TV press the TV key ....Dvd player or VCR, then press that key). (Note: make sure you are aiming the remote at the device so the IR(infrared) enters the device.) Step #2 Press and hold the 'p' key(upper right corner of controller) until LED blinks twice, then release....Step #3 enter the code 9 9 0 ..the LED lite blinks twice. ..Step#4 to get the first number of the code press th e number 1 on the controller...the LED will blink the once for 1 //twice for 2...three times for3...etc...write down how many times the LED blinks(if it doesnt blink the first number of the code is 0) Repeat step #4 to get the remaining numbers, i.e. for the second mumber of the code enter 2...third number enter 3...till you have all four numbers.( when done you can press a different device key to get you off... then press the right device key for your device to operate it remotely. Hope this helps

Aug 31, 2008 | Radio Shack (15-2147) Remote Control

1 Answer

52 in rca tv


does the light blink 3 times when you press power? Let me know exactly what happens when you press the power button. Please respond to this same post when replying.

Aug 07, 2008 | RCA D52W19 52" Rear Projection Television

Not finding what you are looking for?
RCA D52W20 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75846 Answers

jason

Level 3 Expert

905 Answers

matt martin
matt martin

Level 3 Expert

1230 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...