Question about Computers & Internet

Open Question

I need a schematic so I can repair traces on the motherboard ,where can I get one ?

Posted by on

  • Wayne Mineard
    Wayne Mineard May 11, 2010

    You would have to contact the manufacturer of the MB for schematics, but I am doubtful that they would supply them to you.

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: schematic diagram

I have the same problem. Two weeks ago my TV failed to produce a picture, only audio and a black screen. Any ideas?

horsefeatheranch@yahoo.com

Posted on Jan 19, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Schematic acer aspire -e1-571g


Due to the complicity of multi layer boards, schematics are not available. Manufacturers agree that if a motherboard fails under warranty, it is replaced, not repaired, so no need for schematics.

Nov 19, 2015 | Acer Computers & Internet

1 Answer

Asus cg1330-05 motherboard manual


If by schematic, you mean a circuit diagram with all components shown and their values, forget that. There is no such thing. Motherboards are manufacturer proprietary and they do not support independent repair. The "repair facilities" that they authorize are merely there to verify that the board is bad and to determine if the failure is warranted. Then they replace the board. Failed boards are sent back to the factory where they may be repaired or scrapped depending on amount of damage and demand of the board.

Nov 03, 2015 | ASUS Computers & Internet

2 Answers

Looking for a repair manual, schematics, or any other help for troubleshooting


With your request for schematics, I assume that you are beyond the "bible" of basic repair; "Upgrading & Repairing PCs" by Scott Mueller.
The schematics of motherboards are hard to find, but the data on the chips used on the motherboards are available from the chip manufacturer.
I usually use those, and sort of reverse engineer the the motherboard by thinking "How would I design this circuit."
One then finds out how much corner cutting and how many mistakes are present, and sometimes some good ideas.
For this approach you need, at least, an oscilloscope.
Best Regards, Christopher

Jun 14, 2015 | Computers & Internet

1 Answer

I need trace schematic or diagram for power supply board PLCD300PS07


I have the same PS - did you ever get a diagram ? I'm after one too....resistor R100 completely blown so I can't read its value but its either 900Ohm or 100Ohm ?
We might be able to compare symptoms....

Feb 26, 2013 | Televison & Video

2 Answers

I need schematic diagram for toshiba L6450 s4030 for power solution


Go to www.ebay.com Type: Make and model, refine search to mother board.

Apr 01, 2012 | Computers & Internet

1 Answer

Need Schematices


Try posting on some of the guitar forums. The schematics you are looking for are only available to licensed repair persons but you might get lucky and find someone who will send them to you. Be sure to state what model amplifier you want. If you are a tech try looking at some schematics for a similar amp and tracing the circuit.

Jan 21, 2010 | Music

1 Answer

Need schematics for Beheringer MX 3242X


Behringer won't give schematics except to their service agencies... I have tried... I usually wind up tracing out enough of the circuit to repair it.

Jan 17, 2010 | Audio Players & Recorders

2 Answers

DV1000 Motherboard repair


You have to look for a bad connection on MB. You have a broken trace from openning and closing. You need micro-soldering iron to fix it.

Sep 14, 2008 | HP Pavilion dv1000 Notebook

2 Answers

SCHEMATIC Diagram


no need sistamatic digram please elaborate the problem u are facing iam a chiplevel engineer can help u we can repain the computer only on 2 side there are more circuits in inner layers wher we cant repair please elaborate the difficalties you find i might be help to you

Oct 25, 2007 | EliteGroup P4M800PRO-M Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...