- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
When a fault occurs, the touch screen displays a message on how to clear the fault. Some faults indicate customer maintenance, while others require the attention of the Key Operator and/or System Administrator. The following table represents some of the fault codes and their corresponding corrective actions. These may appear in the Print Queue or Faults List available in the Machine Status mode. 002-770 The job template could not be processed due to insufficient hard disk space. Delete unnecessary data from the hard disk. 003-750 No document was saved for the double-sided Booklet Creation feature. Check the setting of the double-sided Booklet Creation feature. 003-751 The specified document area is too small. Select a higher resolution or a larger scan area. 003-754 003-755 An error occurred in the document scanner. Reset the document, and scan again. 003-756 The fax document is completely white. Check that the original is not white, or that the front and back sides have been reversed. 003-760 Incompatible features are selected in the document scan conditions. Check the selected options. 003-761 The paper size in the tray selected by auto tray switching, differs from the paper size in the tray selected at the tray selection. Either change the paper size for the tray, or change the paper type priority setting. 003-763 An error occurred when reading the Gradation Adjustment Chart. Place the chart properly on the document glass. 003-780 Compression of scanned data was unsuccessful. Lower the resolution or reduction/enlargement ratio to reduce the data size, or send the document in smaller segments. 003-795 The reduction/enlargement ratio exceeds the setting range when the scanned document is enlarged/reduced to the specified paper size. Directly enter the reduction/enlargement ratio, or change the paper size. 003-981 Stapling mixed size documents is available only for documents with the same width. Cancel the staple feature or reset the documents with the same width. 005-210 005-275 005-280 005-283 005-284 005-285 005-286 An error occurred in the document feeder. Contact the Xerox Welcome Center.
The E 602- 003 is due to hard disk system error but you can scan it ;run check disk its can fix that problem.
try this, hold on 1 and 9 (from the machine key board) then switch on the copier;
then wait around 1 hour all screen will be white then the copier will display download mode. then switch off and put on the copier.
If the machine is saying "Please Call Service"..You will have to access the Service Call function to determine the exact problem. Press PROG,*,6 Press PROG to select "service call" mode, then press ENTER. The Error Message will be displayed. For example Heater Error, Drum Fuse Error, Inside Fan Error, etc, etc... **Most common (given m/c age.) would be "Heater Error"...which indicates a problem with the Fuser Unit.....if this is the case you will need to contact local Muratec service for parts.
Hope this helps. Please rate my response. Thanks. Have a good day
he E 602- 003 is due to hard disk system error but you can scan it ;run check disk its can fix that problem. try this,
hold on 1 and 9 (from the machine key board) then switch on the copier; then wait arround 1 hour all sceer will be white then the copier will display download mode. then switch off and put on the copier.
sometimes the display of the printer might freeze up due to multiple reasonds like the network settings,some error message, a partial reset might help you resolve some of the concerns as far as the freezing up is concerned but since it is a high end machine i would rather recommend you to perform the trubleshooting under supervision of some good technician.if Thanks a& regards Amit