Question about KitchenAid KSRS25IL Side by Side Refrigerator

2 Answers

Icemaker overflows when filling

I recently moved into my home. I have a Kitchenaid KSBP25FKSS00. When the icemaker fills, it overflows. I had to have my brother disconnect the icemaker until we can figure out what is wrong. Any ideas????

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 833 Answers
Re: Icemaker overflows when filling

First, get your manual here:

The manual describes a wire arm which should gauge the amount of ice your unit produces. That arm is improperly set up or missing. The switch it controls may be defective. Have a look.

Posted on Dec 18, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Icemaker overflows when filling

I have a Kitchenaid KSBP25FKSS00.
How to remove the dispenser pannel cover. Because want to replace some plastic parts. How can I open the dispenser pannel?

Posted on Jun 09, 2012

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My maytag mfi2568aeb french door bottom freezer has ice on coils in freezer and ice maker wont make ice

Sounds like the icemaker drain is clogged and the fill process overflowed the unit. the water then froze the drain and all overflowed water from icemaker. Remove icemaker and remove all ice from freezer and icemaker. Clean all drains. Reinstall.

Nov 19, 2014 | Refrigerators

1 Answer

Frigidaire icemaker still overflowing after replacing inlet valve

Make sure the water is not splashing out the fill tube rather than the icemaker. Sometimes ice forms in this tube and causes the water to shoot over the tube and run down. You could also try turning the water faucet valve down a bit. Your water pressure could be too high and it is filling too fast. Last thing if you have very hard water the cubs could be sticking in the mold tray and not releasing. When the icemaker fills again there is still ice in ther causing the icemaker to overflow.

May 17, 2014 | Refrigerators

1 Answer

GE profile refrigerator pss266msra has a problem with the freezer. Replaced the thermistor and heater as suggested since I had ice buildup. Now icemaker is leaking water which is freezing into icicles -...

One of two things is happening.
1) the fill tube leading from outside the box into the icemaker may have ice buildup or is too close to the icemaker fill wall. Make sure there is a gap between fill tube and wall and check for ice in the tube.
2) wait for the icemaker to call for water and see how long is calls water for. It is only suppose to be 7.2 seconds. If it calls for water longer it can be overflowing. If overflowing than replace icemaker.

Usually there is ice buildup or something that the water is hitting and splashing everywhere.
If you have anymore questions or need more assistance please comment.

Aug 01, 2011 | GE Refrigerators

1 Answer

Icemaker quit making ice .. water supply to drinking water still working ..switch is on the on position

check the fill tube that brings water into icemaker..these sometimes freeze over..if it is, defrost and order new fill valve....or, you have a fill valve thats bad..

Jan 11, 2011 | KitchenAid Refrigerators

1 Answer

Ice cubes stick together as though too much water is coming into tray. Is there a valve or something to control amount of water coming in?

yes their is a water valve , 2 things it could be your valve or you i/m. the i/m tells the water valve to fill for about 6-9 seconds if the icemaker is bad it could be telling it to fill for 10 seconds instead of the normal time and overflow the icemaker ,or the water valve also called solenoid could be bad and at not stopping at the desighned time. i dont have your model # to go much furthur but you can remove the cover in the front of the icemaker and see if you see an icemaker water level adjustment screw, newer ge and frigidaire ref. cannot be adjusted, however wpl, maytag, and older ge ref can be and older frg.try adjusting water level at icemaker first .

Sep 19, 2009 | KitchenAid KSCS25FKSS Side by Side...

1 Answer

Ice maker stopped working

The laser , is supposed to blink . This laser , tells the icemaker to stop making ice , when the bin is full . Pour about 2/3 cup of water into the icemaker . If it doesn't dump the cubes into the bin , the icemaker is bad . Or , if there is ice in the bin , which hasn't dumped , the icemaker is bad . If the icemaker dumps the ice ( from water pour ) , then look above the fill cup , and see if the black fill tube is frozen . If so , then replace the water valve and turn the freezer temp down slightly . It will take several days for this fill line inside freezer to thaw . If icemaker dumps , and black tube NOT frozen , replace the water valve . The valve , is where the wall water line connects to on the refrig .

Sep 05, 2009 | KitchenAid KSRP25FNSS Side by Side...

1 Answer

Water leaking from ice/water dispenser

hi there,

you may have a kink in the water line leading to the icemaker. the leak is due to warm water entering the icemaker itself. i would also check the water valve in the icemaker itself and ice actuators or paddles to any breakage.

Sep 04, 2008 | KitchenAid (KSRD22FKST) Side by Side...

1 Answer

Sub-Zero 632 Ice Maker Leaking into Ice Bucket

Ice Maker is overflowing and leaking into the ice bucket: There are several things to check for.
Go for the easy stuff first, make sure the icemaker is level, some of the plastic liner fridge's will move and allow the icemaker to tilt over and leak. Other troublemakers..... the fill valve
staying on and over filling the icemaker..... the finish sometimes comes off the icemaker body and all the ice cubes don't come out. This will allow the new water to fill on top of an icemaker
that still has a ice cube or two left inside the body, if you have had trouble with black specs in your ice cubes, this may have been the beginning of your finish problem on the icemaker body.
On the module style ice makers (Whirlpool, Maytag Family, Sub Zero) the printed circuit in the
module head often wears and the contacts become too long and allow the icemaker to over fill = new ice maker or new module head.
Older style icemakers: This gear is bad for breaking and the icemaker quits turning to eject the ice.
You can remove the front cover to see the gear.
This is a common parts breakdown of the older style icemakers

Water fill volume: The water fill adjustment screw will change the fill volumes by changing the fill time.
One half to one full turn usually ( approx ) is equal to 20cc ( 0.68oz ) to 40 cc.
The correct fill is usually 130 to 150 cc ( 4.5 to 5.0 oz ).
When a water valve is replaced the fill volumes must be re-checked!

Sub-Zero Service Experts in LA Metro

Aug 15, 2008 | Sub-Zero 632 / S

1 Answer

In door water/ice dispenser not working

check the connect part, see if the gears in the right position.

Jun 17, 2008 | KitchenAid KSRS25IL Side by Side...

1 Answer

Icemaker (whirlpool)

i suggest you replace is sending signal to water valve.

Jun 22, 2007 | Hotpoint  15.8 Cu. Ft. Top-Freezer...

Not finding what you are looking for?
KitchenAid KSRS25IL Side by Side Refrigerator Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4625 Answers

mike cooper

Level 3 Expert

864 Answers

rugby prop

Level 3 Expert

426 Answers

Are you a KitchenAid Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides