Question about Nokia 6288 Cellular Phone

1 Answer

Headset Mode My daughter has put my phone on to headset mode so I can't hear people without using my headset. How do I turn this off. Thanks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

If it is a  Bluetooth headset just go to 'Bluetooth Menu', 'Active Devices' and select 'Disconnect'.

If it is connected via a cable just pull the cable out of the phone.

Hope this is of help to you,
Fone Fixer.

Posted on Dec 28, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to put peltor bluetooth into pairing mode


Normally Peltor headsets work as follows:

1.) Turn the device off.
2.) Once off, hold the on/off/mode button for 5 seconds until you hear a voice say "pairing mode"
3.) Make sure bluetooth is active on your device and search for the Peltor headset, once you find it select it.
4.) When prompted for a pairing key use 0000
that is 4 zeros.
5.) Headset should say pairing complete.

As with moth bluetooth devices remember this muse bt done within a normal amount of time so have your device ready to search by time you put headset in pairing mode will help.

Dec 22, 2012 | Peltor MT53H7BWS2 Bluetooth Headset

1 Answer

Would like to know how to turn headset back off...


hi :) wanna ask your phone has water damage right ?? ok,if some water has been remain at the area of charging or headset port,will make your phone show in headset mode,when i n headset mode,that why u cant hear people talking.but once u plug in headset,i sure u can hearing.it cant be solve even how many time u turn on and off your phone. what to do ?? u should send for technician open up your phone to clean up inside.
if my solution useful,please give me rank. thanks.

Jul 19, 2010 | Pantech Matrix Cell Phone

2 Answers

How to use bluetooth headset in samsung corby???? plz plz help me


Hi,
1. Just activate the bluetooth in your mobile.
2. Put your bluetooth headset in discovery mode (for this you may need to press the ON button in your headset for more no. of secs around 15 secs) . Please read the user manual of your bluetooth headset to know about how to put it in discovery mode.
3. After that, search for bluetooth devices in your samsung mobile.
4. your headset should be detected in your mobile. If not, still your bluetooth headset is not in discoverable mode. you have to turn it on and try again.
5. If listed in your mobile, select it and it may ask for Passcoe. Provide 0000 as passcode. Thats all now the bluetooth headset is connected to your mobile. If passcode is not accepted, then please do refer the device manual to know about that.

I hope this is useful to you.
Thanks

May 04, 2010 | Samsung S3650 Corby / S3650 Genio Touch...

1 Answer

How do I put it in discover mode?


How to Pair Cardo S-800

1.Turn on your phone and turn ON its Bluetooth function.

2.Make sure the headset is turned OFF, then press and hold the Power Button for approximately 8 seconds until the LED status indicator begins alternating blue and red, indicating that the headset is in Pairing Mode.

3.Set the phone to search for Bluetooth devices by following the instructions in the phone’s user guide. This is usually found in the phone’s Bluetooth menu and may be referred to as “discover” or “add” a device. (Settings > Connectivity > Bluetooth - turn ON - > Discover Devices)

4.After a few seconds, the phone will list the “Cardo S-800” as a discovered device. Select it from the list and press “oK” or “yes”.

5.When prompted, enter the passkey “0000” (4 zeros) and press “oK” to complete the pairing
6. When the pairing pairing is successful the headset’s LED status indicator will begin flashing.

You should now be able to make and receive calls using your headset. To initially connect the headset to your phone, you may need to tap the CTRL Button once on the headset. iMPortAnt: if pairing is not completed within 2 minutes while the Pairing Mode is activated, the headset will return to Standby mode, flashing blue once every three seconds and you must start the Pairing process again from Step 2 above.

If you found this information helpful, please give me a big thumbs-up when you rate my answer. Thanks.

Feb 07, 2010 | Cardo S-800 Bluetooth Headset Wireless...

3 Answers

How to pair my blue parrot b250 with my phone lost my notes on how to pair


1. Turn headset off (panel 5).
2. Hold down the headset’s MFB until the red and blue lights
flash and you hear 2 rising tones, followed by 4 more tones.
Important: Wait for all tones and for both lights to flash. This
may take up to 15 sec. Release the MFB.
3. Follow the manufacturer’s instructions for putting your
cellular phone into Bluetooth discovery mode.
4. Wait 5-15 sec. while the devices discover each other.
When the phone discovers the headset, select “Pair” and
enter a passcode of 0000 when instructed. When pairing
is complete the headset’s blue light will stop flashing and
the phone will prompt you to ‘connect’ to the headset.
Enter “Yes” on the phone to connect to the headset. When
connected, the blue light will flash indicating that the
headset is in standby mode ready to receive a call.

USER GUIDE


Jan 03, 2010 | VXI Corporation Blueparrott B250-XT...

1 Answer

When I am talking to someone on the phone i get a lot of static.


see what TTY mode your phone is in. TTY mode is under call settings or go to voice command and say TTY mode. I keep mine off. This mode is for people who are deaf, and people who are hard of hearing and use hearing aids.

Dec 12, 2009 | Plantronics Discovery 925 Bluetooth...

2 Answers

Sony ericsson bluetooth headset tryin yo connect


Be sure the the headset in in 'Pairing' mode.
When in pairing mode, the light should be flashing red and blue or have a steady blue.
The put most headsets in pairing mode, turn headset OFF, then hold the power button until it goes into pairing mode as discribed above.
Then you can discover it with your phone or PC. Pin (pass key) should be 0000 (4 Zeros) or try 1111, 1234, 9999

Nov 18, 2009 | Sony Ericsson Mobile Bluetooth Car Kit...

1 Answer

My phone is at headset mode. but i do not have a headset. thats why i cannot hear the other person on the line. so how can i put it back to handsfree mode? wherein i can use the loudspeaker and all?


Sometimes dirt/debris gets in the headset jack on the phone causing the circuit to close which makes it think there is a headset in it. Try to take a headset and insert and remove it a few times to get the contacts unstuck. Liquid damage can also cause this problem.

Nov 13, 2009 | Nokia N70 Cellular Phone

1 Answer

New Phone Causing Echo


It sounds like your microphone volume is too loud. Get someone on a call with you so they can tell you how it sounds as you adjust it. Turn down the mic volume by pressing the + & - buttons on the earpiece together once which puts the earpiece into mic adjust mode. Then decrease the mic volume by pressing the minus button a few times until it sounds right. The earpiece will automatically revert to normal mode within a few seconds.
If this doesn't work it may be that you need to adjust the compatibility setting for the new phone. This is the small black dial on the base station. The most common setting is 'A' but you may need to experiment with other settings for that phone.

Nov 04, 2008 | GN Netcom GN 9120 Professional Headset

1 Answer

Nokia 6288 - Can't hear


see buddy i dont thinks so that it can automatically go to the headset mode, might be the issue is with the default speaker in ur handset, consult ur vendor for the concern.

Dec 18, 2007 | Nokia 6288 Cellular Phone

Not finding what you are looking for?
Nokia 6288 Cellular Phone Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nokia Cell Phones Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

270rexton
270rexton

Level 3 Expert

782 Answers

Are you a Nokia Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...