Question about Sharp XR-10X Multimedia Projector

1 Answer

At 9 mos...no power...no lights...no functions...Is there a reset

Does anyone know if there is a reset button within the Sharp xr-10x DLP projector. We had ours since last holiday season and it just went out...totally--no power...no lights...no functions. Hoping there is a reset button...as it appears to be more than a blow lamp (note our lamp had only 300 hrs) so I will not purchase a replacement (approx $190-$300 w/various online sources) until I can determine if the unit works. Sharp, of course will not warranty anything beyond the "90-day" warranty period--which is ridiculous for a $600 projector. Hope someone out there has an answer.

Thanks,

Posted by on

  • cdb_pups Sep 28, 2009

    Solved my own problem with help from a previous post from 'fixya'

    Hi, I just opened my Sharp xr-10x DLP projector today, which had no
    power, no lights, no functions. A previous post worked for me...Remove
    the 6 screws on the bottom of the unit (you'll need a longer phillips)
    and the two screws on the back, toward the top of the unit. Obviously,
    be sure to keep these handy for reassembly (I have two curious dogs and
    a 4 year old to contend with). Then, to remove the housing...use a std
    screwdriver and slightly pry the cover off from the rear of the unit.
    This should losen allowing you to pivot the cover forward and then off
    from the projector lens. If you need to reset your unit, the reset
    button is near the lamp, not the lens (to the side of the lens). It is
    a small red button--depress this. Next, you can connect the ac cord
    and try powering up the unit. For me, I got a blinking red light but
    could not power up the unit. I then opened up the lamp compartment on
    the bottom of the unit (2 srcews) and remove the lamp. Next reconnect
    the lamp...when doing so, make sure the two prongs fit the lamp--this
    is the power supply. Then replace the lamp cover and retest the unit.
    At this point, my projector powered up as it used to. Finally replace
    the projector cover...from the lens then backward. Tighten all screws
    and you, hopefully will be ready to use the projector again.

    Keep
    in mind, your problem may be the need for a replacement fuse or lamp.
    The fuse should be available at an electric supply shop or a Radio
    Shack store. I have seen replacement lamps for $190-$275 available
    online.

    Good Luck...Hope this helps you out. As I said, I just
    completed this process myself today and am happy to have avoided the
    shipping costs and $65 diagnostic fee + labor and parts to have Sharp
    repair this. We are looking forward to 'movie night' on the 8' screen
    tonight! Hopefully, you'll be enjoying your projector soon!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This worked GREAT for me! Fixed my problem!

Posted on Jan 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Projector sharp XR-H325SA indicating lamp I replace tha new lamp but still indicating ineed to reset lamp timer but how?


hi,
for resetting the lamp hour do the following

1. Plug the power cord into the AC socket of the projector.
2. While simultaneously holding down MENU/HELP, ENTER and DOWN ARROW button on the projector, press STANDBY/ON on the projector.
3. "LAMP 0000H" is displayed, indicating that the lamp timer is reset.

ajin_g_25.gif
ok

Jan 24, 2011 | Sharp XR-10X Multimedia Projector

1 Answer

I have replaced the lamp on my sharp xr-10x L. I cannot get the bulb to turn on I have lights so there is power but the lamp is not on.


You must reset the lamp timer. Check the manual or sharp website for instruction how to reset the timer after changing the lamp

Aug 07, 2010 | Sharp XR10XL DLP Projector

1 Answer

Unlock Sharp XR-10X-L Notevision Proj. says keylock function on


According to pg. 45 in the owner's manual, you turn Keylock function ON by holding down the ENTER key on the projector for about 5 seconds while the projector is being turned on.

To take the Keylock off-- Hold down the ENTER key on the projector for about 5 seconds. If the projector is in standby mode, you can release the keylock by holding down ENTER and STANDBY/ON keys simultaneously for about 5 seconds.

Apr 27, 2010 | Sharp XR-11XC DLP Projector

1 Answer

My Sharp XR-10x has no power or lights. Has worked and now does not.


if there are no leds lit, the bimetal breaker has probably tripped. remove the top case (6 screws on the bottom and the top 2 on the back). find the red button on the front of the lamp housing and press it. if it clicked, it has reset and will now work. if it didn't, you have a bad power supply. while you have the projector open, blow the dust out of it with canned air.

Dec 28, 2009 | Sharp XR-10X Multimedia Projector

2 Answers

XR-10X/XR-10S - Can't find a way to open up the lid!


maybe your Sharp XR-10X are damage so you want to know what will you do??

Sep 17, 2009 | Sharp XR-10X Multimedia Projector

1 Answer

Sharp XR-10X/XR-10S - CAN'T FIND THE RESET BUTTON


Hi, I just opened my Sharp xr-10x DLP projector today, which had no power, no lights, no functions. A previous post worked for me...Remove the 6 screws on the bottom of the unit (you'll need a longer phillips) and the two screws on the back, toward the top of the unit. Obviously, be sure to keep these handy for reassembly (I have two curious dogs and a 4 year old to contend with). Then, to remove the housing...use a std screwdriver and slightly pry the cover off from the rear of the unit. This should losen allowing you to pivot the cover forward and then off from the projector lens. If you need to reset your unit, the reset button is near the lamp, not the lens (to the side of the lens). It is a small red button--depress this. Next, you can connect the ac cord and try powering up the unit. For me, I got a blinking red light but could not power up the unit. I then opened up the lamp compartment on the bottom of the unit (2 srcews) and remove the lamp. Next reconnect the lamp...when doing so, make sure the two prongs fit the lamp--this is the power supply. Then replace the lamp cover and retest the unit. At this point, my projector powered up as it used to. Finally replace the projector cover...from the lens then backward. Tighten all screws and you, hopefully will be ready to use the projector again.

Keep in mind, your problem may be the need for a replacement fuse or lamp. The fuse should be available at an electric supply shop or a Radio Shack store. I have seen replacement lamps for $190-$275 available online.

Good Luck...Hope this helps you out. As I said, I just completed this process myself today and am happy to have avoided the shipping costs and $65 diagnostic fee + labor and parts to have Sharp repair this. We are looking forward to 'movie night' on the 8' screen tonight! Hopefully, you'll be enjoying your projector soon!

Sep 16, 2009 | Sharp XR-10X Multimedia Projector

1 Answer

New bulb in now wont work - no power - wont turn on to reset lamp


first, make sure you have the correct lamp. the lamp for the xr-10x-l looks like the xr-10x, but the plugs are different (common mistake). make sure you have the AN-XR10L2/1, not the AN-XR10LP/1. to reset the lamp timer (with the projector plugged in but off), hold down the enter, down arrow, and menu buttons and press the power.

May 30, 2009 | Sharp XR-10X Multimedia Projector

1 Answer

XR-10x bulb timer has timed out. How do I reset the projector?


you need to reset the lamp timer see http://www.ercservice.com/PDF/Lamp-Sharp-XR10-XR20.pdf

Apr 07, 2009 | Sharp XR-10X Multimedia Projector

Not finding what you are looking for?
Sharp XR-10X Multimedia Projector Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

255 Answers

k24674

Level 3 Expert

7993 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...