Question about RCA D52W20 52" Rear Projection HDTV-Ready Television

1 Answer



Posted by on

  • CHRIS Jan 18, 2009




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 4,402 Answers

Those sets are notorious for having many problems causing what you're describing. The power supply/deflection board is avaliable aftermarket via PTS. Too many things that can cause that to hazard a $$ price.

Posted on Dec 17, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sharp aquos tv, model no. lc-70c-6500u, no audio, visual at power up, standby/power light flashes 2 times long, 5 times short, nothing else happens, what is this mean?

Sounds like main board fault. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Jul 28, 2015 | Sharp Televison & Video

1 Answer

Machine won't work.

Robert. You have a bad water valve OR completely clogged up filter screens on the valve. My past experience with this machine with this type of problem is to replace the valve assembly. part Number W10364988

Apr 09, 2014 | Maytag Bravos Series MVWB300WQ Washer

1 Answer

Green power light flashes 3 times then repeats

The defect is likely a sensitive component to over voltage (lightning) on the main power supply. But you should not exclude other boards too, since ohter board also have local power supplies and sensitive CMOS integrated circuits. Check all MOSFET transistors on the the main power supply, since they are the most sensitives. Also the regulator IC to control the PWM sent to the MOSFET is made of CMOS (sensitive). Then check all the diodes even if they are more robust to lightning. There is a MOV that absorb the lightning that could be shorted but in your case it seems to have survived.

Sep 21, 2017 | Toshiba 55ZV650U 55 in. LCD HDTV

1 Answer

How do i reset the service light on a bhm (voyager) v4 ceiling hoist?

To turn off the service light that is flashing red on your V4 BHM ceiling lift, you have to proceed this way:
1- Power off the lift with the red cord
2- On the hand controller, push on the PROG + RETURN button at the same time and maintaint it
3- Power on the lift
4- Keep pushing on both buttons, and push in order: UP, DOWN, LEFT, RIGHT.
5-The green light will flash and the buzzer will beep 5 times
6- Release all buttons on the hand controller.
7-Push on the UP button many times, till your hear 4 beeps
8-Push the PROG button once.
9-Push on the LEFT button many times, till your hear 3 beeps
10- Push the PROG button once.
11-Power off the lift with the red cord, then back on.
The service light should be off.

May 25, 2011 | Health & Beauty

1 Answer

I have to get a printout... When I went to my IP2200, I found several pages jammed. I simply pulled them out and rebundled the paper and set them in the feed tray. I then pushed the resume button, which...

Hi. In such situations it is best to reset the printer.
This procedure resets canon iP1200 /iP1600 / iP2200 printers.

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal.

Jul 29, 2009 | Canon Office Equipment & Supplies

1 Answer

Presario v2000 stuck in hibernation, can't power it up

remove battery plug in power...see what happens ...nothing happens press and hold power button until you hear response(shut down)press power as usual to boot.if it doesnt work first time try a few times more remember to keep power button pressed to shut down.

Oct 19, 2008 | Compaq Presario R3000 Notebook

2 Answers

My big screen tv went off and reset it but you push the button and the power comes on and goes right back off

when we push power button the green light flashes as if thinking about turning on and nothing happens, any way to fix this? 

Feb 18, 2008 | Televison & Video

1 Answer

Filter light still on "Red"

try holding ice type and child lock together for 3 seconds that worked on mine

Mar 30, 2007 | Maytag MSD2454G Side by Side Refrigerator

Not finding what you are looking for?
RCA D52W20 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74990 Answers


Level 3 Expert

905 Answers

matt martin
matt martin

Level 3 Expert

1213 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides