Question about Asrock P4I45D Motherboard

1 Answer

I have 2 sticks of Kingston pc 2700 ram for my p4I45d Motherboard and it will not boot any suggestions

Posted by on

  • cbrinston Sep 27, 2009

    I get no beeps the computer powers up but does not get to post and does not try and boot

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

If it is the ram you should hear continuas beebs

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does memory upgrade for biostar k8m800-mam2 motherboard cause memory error beeps?


I would verify that the memory you're using is actually working properly.
Try to boot to the new stick and see if it works.
If not, it doesn't work.
If it does, you may need to replace the original stick with the same stick that you are trying to use now.
Use this site as a guide.
http://www.crucial.com/store/listparts.aspx?model=K8M800%20Micro%20AM2&Cat=RAM

Dec 22, 2011 | Biostar K8M800 Micro AM2 Motherboard

1 Answer

I have an emachine T5026. Emachine tech swears this machine only supports pc2700 ram but the stickers on the factory installed ram says pc3200 256mb x 2 so i bought 2 memory masters pc3200 1gb x 2 sticks....


PC3200 is backwards compatible with PC2700. Meaning you can install PC3200 into your motherboard but it won't run any faster than would PC2700, however it will not cause any harm and should work fine.

Emachine's would say you need PC2700 most likely because they're trying to sell you some.

One of your new memory modules or the memory slots on your computer may be defective. I recommend installing a single stick of memory and booting your system. If it is successful then shut it down, disconnect the power and install another stick. Boot again and keep doing so and by process of elimination identify the bad memory stick or the bad memory slot.

This is the "likely" cause and isn't too uncommon.

Good luck.

Sep 07, 2010 | E-Machines eMachines Desktop PC

2 Answers

I got a message that said I had insufficient memory. Something is wrong because I installed istalled 3 Kingston memory sticks KVR 400/512R. I removed the sticks and reinstalled them. Now when I turn...


Try placing one stick at a time in and powering up. It sounds like you have a memory problem (a stick may be bad).

If it powers fine, then power it down and change the memory, and try again to see if it fails on one.

May 26, 2010 | Gateway 507GR PC Desktop

3 Answers

I am trying to install new RAM on my mother's Sony VAIO PCG-K25 laptop. It had two slots, each with 256MB sticks in them. I replaced these with 512MB sticks, and the computer wouldn't boot. It wouldn't...


make sure they are compatible with your computer, there are alot of electronic stores (circuit city) was the worst at it, but will sell you the wrong ones and say they are backwards compatible.. usually P4 2.8 can run PC2700, some run PC2100, which im hoping yours is PC2700... if so, make sure they are NON-ECC also... i would just get 2 1 gig PC2700 DDR 200pin sticks and stick em in... good luck

Nov 07, 2009 | Sony VAIO PCG-K25 Notebook

1 Answer

I have a abit v17 mobo want to get max ram (2gb) bought kingston value ram from kingston rep said it would work. also have corsair matched memory also was told by rep that it would work. I plug them in and...


Your motherboard supports DDR SDRam I assume the ram sticks you bought fit in the socket correctly and are the right way round?
Try the computer with each ram stick seperately. Just because ram is new doesnt mean its not defective.
What configurations do you have?
Are you using two corsair sticks or two kingston or a mix of both and what models are they?

Jun 19, 2009 | Computers & Internet

1 Answer

Cannot boot up


maybe you must reset the bios in the motherboard. try to open your system then look for a 3 pin in the motherboard near in the CMOS battery.. it has a number 1,2 and 3 it is called jumper settings.... try to put the pin in number 2 and 3 then w8 after 10 seconds then gput it back to 1 and 2 in try to boot up.. ^^ i wish this could be help.. ^^

Feb 06, 2009 | Albatron Nforce2 (KX18D PRO II)...

4 Answers

Want to upgrade ram to 1gb


Kingston Value Ram will do, nothing over 533mhz

regards

Nov 24, 2008 | EliteGroup P4M800-M7 Motherboard

Not finding what you are looking for?
Asrock P4I45D Motherboard Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asrock Computers & Internet Experts

David
David

Level 3 Expert

778 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Computer Links

Level 3 Expert

2385 Answers

Are you an Asrock Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...