Question about Kenmore 22422 Top Load Washer

1 Answer

Bottom part of agitator does not work, i replaced the clutch dogs two weeks ago for the top part. kenmore series 80

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,937 Answers

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number and you'll see a list of major sub-components with diagrams and parts.

There are a number of Series 80 design washers. You'll need the actual model number to better check for the problem.

First, I'd remove the top agitator (as you've already done), then I'd remove the main agitator.

Under it you will see a clip and what Whirlpool calls a "washer". The "washer has two prongs, one fits into the main agitator shaft drive and the other fits in the lower agitator. If one or the other of the prongs is broken, the agitator most likely wont. I'd also look inside the main agitator to see if the ridges are broken off.

I'd then start the washer on it's smallest cycle and see if the main agitator shaft turns back and forth. If it doesn't and the washer goes through it's drain and spin cycles, the problem is likely in the transmission itself with what they call the agitate gear and / or agitate cams.

Please see the Whirlpool / Kenmore PDF document on installation, maintenance and operation of direct drive washers.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6?OpenView&Start=1

This is a Whirlpool document with parts lists for their commercial washers (basically the same as the consumer models)

If the problem is in the transmission, although it looks complicated, it really isn't that bad if you have a moderate level of mechanical ability.




Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Series 80 washer. Agitates too slow


check the dogs in the agitator take off the cap it should rachett if it turns free replace the dogs in the agitator

Jul 12, 2010 | Kenmore 24032\24036 Top Load Washer

2 Answers

80-series w/ broken top agitator


There is a video at www.appliancehelponline.com/servicemanual.html that will walk you thru the replacement of the agitator dogs, this is a common problem with this style washer.

Mar 28, 2010 | Kenmore Washing Machines

1 Answer

Series 80 Agitator top dosent work


If the bottom agitates and not the top, the problem is likely the 4 "agitator dogs" designed to allow the top agitator to turn only one way.


I assume that your model number starts with a 110 instead of 100.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?modelNumber=110.26842692

Look at the section on the Sears site for Agitator, basket and tub.

See the part "Dog, agitator "

Remove the fabric softener unit, lift the top agitator cap (use a screwdriver) and you should see a plastic part in the center of the top agitator with a 1/2" square drive.

Remove the drive and lift off the top agitator. Turning it over you should see the 4 "dogs", replace these and the top agitator should turn in one direction only.

Replace the 1/2" drive, the cap and fabric softener unit and the top agitator should work.


Following is an illustrated description of the above.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=136&osCsid=0da65cea0e338fe930b1fde153a243f0


Jan 09, 2010 | Kenmore Washing Machines

1 Answer

Agitator: bottom moves, top does not


If the bottom agitates and not the top, the problem is likely the 4 "agitator dogs" designed to allow the top agitator to turn only one way.

On the Sears parts site:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?pop=true&modelNumber=110.26902691&pop=flush

replace the 110.26902691 with your model number (lift the lid and the model number should be printed on the cabinet) and look at the section on the Sears site for Agitator, basket and tub.

This is what they look like:

pd_26_110_80040?$pddetailsth$ #21 on diagram Dog, agitator (4) Number:3366877Substitution:80040 $9.25Remove the fabric softener unit, lift the top agitator cap (use a screwdriver) and you should see a plastic part in the center of the top agitator with a 1/2" square drive.

Remove the drive and lift off the top agitator. Turning it over you should see the 4 "dogs", replace these and the top agitator should turn in one direction only.

Replace the 1/2" drive, the cap and fabric softener unit and the top agitator should work.

Sep 13, 2009 | Kenmore 23822 Top Load Washer

1 Answer

Replacing the agitator dogs in a Kenmore 80 series washer


Hi, Remove the cap on the agitator and then remove the inside cover. There is a 7/16" bolt under the inside cover. Remove the bolt and the agitator will lift out. Seperate the 2 pieces of the agitator and replace the dogs. You might have to use a flat blade screw drive and punch out the 4 tabs around the bolt hole in the agitator if this applies.
I hope this helps you. Please let me know if I can assist you further.

Vic

Jul 03, 2009 | Washing Machines

1 Answer

How to remove the agitator on a Kenmore 70 series


Set the agitator down and hold with your feet. Grab the top part and pull up sharply. It will come off. some are harder than others.

May 18, 2009 | Kenmore Washing Machines

1 Answer

Kenmore series 80 washer: does not twist in the middle


Check the agitator by turning it back and forth. It should work like a ratchet (turns one way, locks the other way).If you're able to turn it in both directions, the agitator dogs are worn and need to be replaced.
Remove the agitator cap and the bolt that holds down the agitator. With the bolt out you can remove the top section of the agitator (auger) where you should see 4 small white or beige plastic gears (dogs). Replace those and it should be ok.
12763ce.jpeg
Part number is 80040

Let me know if you need more help.
Good luck!

Apr 01, 2009 | Kenmore Washing Machines

1 Answer

Agitator not working - how do you take it apart - Kenmore 80 Series washer


Pop the top off the agitator. There is a slot for a flat screwdriver on the top side.
Remove the 7/16 bolt.
Pull the agitator apart.
Replace the agitator dogs inside the top part.
Parts about $5.00.at any appliance parts store.

Mar 14, 2009 | Kenmore 23012 Top Load Washer

1 Answer

Kenmore series 80 model 1102983120 older top agitator gone


if just the dogs are gone you can replace them wim any agitaor dog kit. I usually use whatever kit was cheaper when i order abd put just the dogs on. never had a problem yet.

Jan 26, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 80 series


replace the dog set in the agaitator some have a 4 dog set part number 285770 and these are white some have a 2 dog set the part number is 358692 replacing these dogs will fixya

Apr 07, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5467 Answers

Mike Squire

Level 2 Expert

391 Answers

Robert Rankin

Level 2 Expert

338 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...