Question about Reebok 8700 ES Treadmill - Silver Service Delivery!

1 Answer

My console does not allow me to change the incline, speed, etc. The control panel does not acknowledge the buttons pushed. I've turned it off and on.

Posted by on

  • 3 more comments 
  • minniesue Oct 15, 2009

    We found out we had to have a new console. Thanks anyway for the reply.

  • minniesue Oct 15, 2009

    No. It was the console that has to be replaced.

  • Chad Gilbert May 11, 2010

    do any buttons work at all? The start buttons?

  • Terry Richardon Aug 15, 2013

    Incline button works. Sometimes when I plug it back in the belt runs one mile per hour but still no buttons (except incline) work.

  • Terry Richardon Aug 15, 2013

    Also, if I hold the incline button down I can press any button on the consul and get a beep. I'm assuming then that all the buttons area able to receive or send a signal. I wonder if there is a short in the incline switch or motor.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My treadmill is doing the same thing. the only buttons that work are the start; incline up. 4 incline; 8 incline; and 11 incline.

Posted on Oct 14, 2009

Testimonial: "He asked the right question."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CONSOLE HAS NOT LIGHTS


Can you change the illumination setting like in a car? The lights are most likely LEDs which dont just burn out. and are independent.

Apr 05, 2014 | Exercise & Fitness

1 Answer

I have a Proform 1026 EXP treadmill that began running at full speed whenever it is turned on. The incline controls function normally but the belt speed is incredibly high. When set to 1.5 MPH (the slowest...


please run the Software calibration see the instruction.
GOD BLESS you
The Steps for Newer Style Console Calibration
1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10. Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Sep 18, 2013 | Proform 1026 Exp Treadmill Motor Control...

1 Answer

Enginerring mode not working


follow the next steps and fix it.God bless you
The Steps for Newer Style Console Calibration
1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10. Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jun 28, 2013 | Exercise & Fitness

1 Answer

Horizon treadmill model ls925t will not allow the grade to be adjusted. It is stuck at the highest grade


RUN THE SOFTWARE CALIBRATION. God bless you

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.



Apr 02, 2013 | Horizon Exercise & Fitness

1 Answer

Horizon treadmill won't incline


Step 1:

see the diagram attached.

Clean the motor, lube the gear+shaft
Adjust the small POT for a little.
RUN the software calibration for troubleshooting. see the diagram
2_8_2013_11_10_42_am.gif

Step 2:

2_8_2013_11_11_14_am.jpg

Step 3:

2_8_2013_11_11_47_am.jpg

Step 4:


he Steps for Newer Style Console Calibration
1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10.Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
God bless you

Feb 07, 2013 | Horizon Fitness Horizon T101 9 Program...

1 Answer

5600t speed adjust does not work


RUN the software calibration, for troubleshooting and fix it.
See the steps for calibration.
God bless you

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the

    "F" appeared in). Troubleshooting the failure would be the next step

Jan 09, 2013 | Keys Fitness 5600T Treadmill Drive Motor

1 Answer

Treadmill belt runs too fast and will not power off with control panel


Step 1:

test the speed sensor,m for open or faulty, clean it, and tight the connector. see the diagram attached.
However follow the steps for RUN the.s calibration for fix it.
God bless you
1_7_2013_11_03_18_pm.gif

Step 2:

The Steps for Newer Style Console Calibration:
  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
  10. Press ENTER. You should see "SS" or "55" in the console.
  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jan 07, 2013 | Exercise & Fitness

1 Answer

Proform Sport 1000 - The right hand side of my controls which allow me to change the speed of the treadmill do not work. The left side is still operational and allows me to change the incline and select...


Remove the console from the treadmill and remove the back
remove and replace the ribbon cables that run from the keypads to the control board (they are flat plastic strips that push into the board).
remove and replace all the connections on the console
reattach the console and calibrate by doing the following:
1. With the key off press the speed + and stop buttons at the same time and hold
2. place the key on and release the buttons
3. press the stop key once
4. press the speed up til it reaches 85
5. if your max speed is 10 mph then it should read about 9.8-10.2

If the keys will not work then the console is bad and would need replaced.

Aug 09, 2010 | Proform Sport 1000 Folding Treadmill...

1 Answer

The Nordic Track machine's controls seem to be stuck. If I press any button other than "3 mph", it fails to respond and nothing happens. However, when I press the 3 mph button, it will only stay at the 3...


Remove the console from the treadmill and remove the back
remove and replace the ribbon cables that run from the keypads to the control board (they are flat plastic strips that push into the board).
remove and replace all the connections on the console
reattach the console and calibrate by doing the following:
1. With the key off press the speed + and stop buttons at the same time and hold
2. place the key on and release the buttons
3. press the stop key once
4. press the speed up til it reaches 85
5. if your max speed is 10 mph then it should read about 9.8-10.2

If the keys will not work then the console is bad and would need replaced.

Jul 22, 2010 | Nordic Track NordicTrack Treadmill, A2550

Not finding what you are looking for?
Reebok 8700 ES Treadmill - Silver Service Delivery! Logo

Related Topics:

1,234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Reebok Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Are you a Reebok Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...