Question about Motorola Mobility RAZR V3i Cellular Phone

2 Answers

Sound Incoming sound in set very weak and secondly call get disconnect before completion.

Posted by on

  • dharmindar Dec 17, 2007

    what the hell is this... this seems all crap.. making fool of people

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 67 Answers

YOU MUST CHANGE THE BATTERY IT IS MUL FUNCTIONING OR IT REACHES ITS DEATH NEAL.ADVICE BY DOGY

Posted on Dec 20, 2007

Ad

Hi,
my phone is not a motorola isnokia so i dofix a phone but this one i don`t get a pont for it,my email adress is johonlarg@yahoo.com.
thanks

Posted on Dec 17, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My icom ic v8 is weak on receiving...pls help


Is it week because the incoming signal is coming from further away or is it coming from down the street . Maybe the problem is on the other end,the incoming signal is not strong enough.Lots of reasons.

Jun 04, 2012 | Icom Ic V80 Vhf Handheld Two Way Radio...

1 Answer

No sound on incoming call"


This is due to failure or weakness of the Microphone in the phone. To confirm you can connect a hands free headphone unit which can be tested to confirm.If the caller can hear you then it is confirmed that the mic section in the phone is faulty and must be opened to check.

Jun 15, 2011 | Cell Phones

1 Answer

Low ringing volume during first few seconds of incoming call...how can i solve this


ur mobile incoming call setting u assigned low type.

u change the mobile setting

setting>>profile>>edit >> incoming call >> choose ur type incoming ring type,

( or )

ur speaker problem change it immediately

Sep 08, 2010 | Samsung Omnia II I8000 Smartphone

2 Answers

Microphone has completely disconnected, no incoming sound,caller can hear you


your phone's ear speaker needs to be replaced.....goto the repair shop

Oct 23, 2009 | Sony Ericsson K800i Cellular Phone

1 Answer

Mitel sx-20 trunk interrogation function codes


From a DTMF station set installed as the test line on equipment #1, go into trunk group programming (Command #66)
The SX-20 display will show programming registers.
A B C D E F G H
A,B = Trunk equipment Number (1st trunk should be displayed)
C = Register 1
D = Trunk Group Membership 0 = Incoming only
1 = Group 1
2 = Group 2
3 = Group 4
4 = Group 4
E = Trunk Type 0 = Standard CO Trunk
1 = Dictation Trunk
F = Reversal Meaning 0 = Not Incoming of Disconnect
1 = Incoming Call
2 = Incoming Call or Disconnect
G = Disconnect Timing 0 = 60ms
1 = 500ms
2 = 1.5 sec
3 = 4 sec
H = Start Type 0 = Loop Start
1 = Ground Start
Move to the appropriate register using the ENTER/NEXT function (star key).
Change the data as required.
Exit programming (# key)

Hope this helps!

Mar 25, 2009 | Lands Phones

1 Answer

No sound, no outgoing call jamin imate


I dissambled my iMate JAMin and found that one of the wires for the speaker had been broken, they seem to be pretty weak - resoldered the wire now speaker works fine.

Jan 28, 2009 | i-mate JAMin Smartphone

1 Answer

Tone delay


Here is a link to the operating manual which may help :
http://service.us.panasonic.com/OPERMANPDF/KXT7720.PDF

You could try disconnecting the phone by unplugging it for abaout 10 seconds, then all phone settings would revert to manufacturers default settings.

Jan 21, 2008 | Panasonic KX-T7730 Corded Phone

1 Answer

Frames freeze every few seconds


Sounds like a weak cable signal. Contact your cable service provider and ask to have a tech check your incoming line strength.

Sep 10, 2007 | Toshiba 72MX195 72" HDTV

Not finding what you are looking for?
Motorola Mobility RAZR V3i Cellular Phone Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorola Mobility Cell Phones Experts

Virgil Wolter

Level 1 Expert

29 Answers

vince

Level 3 Expert

1216 Answers

D. E. Hev

Level 3 Expert

1181 Answers

Are you a Motorola Mobility Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...