Question about Intel Server Platform SPKA4 (SKOC2HI)

1 Answer

Raid problem dear sir, i create a raid-1 but he does not show the partion.plz clear my raid cocept

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers
Re: raid problem

After creating a raid, you have to create a logial drive in this RAID. After creating a logial drive your operational system can "see" this drive as a phisical disk.Then you can install the operational system.
Let me know if this post help.

Posted on Dec 17, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My hp proliant dl380 g7 server shows non disk error

Enter RBSU create Raid & Select Direct Attached Storage option in boot controller,

May 17, 2012 | HEWLETT-PACKARD HP ProLiant DL380 G7 Entry...

1 Answer

Raid Driver

send me you querry clearly to my email id:-

Mar 15, 2012 | IBM System x3200 M3 7328 Server tower ...

1 Answer

Can not setup RAID 1 on an IBM X3200 M3 Server

you can access the raid controller using the BIOS and system devices>>> refresh>>> then select the controller then create your raid...

don't know why they move out from the POST the controller its really stupid''' Sorry..

Feb 04, 2012 | IBM System x3200 M3 7328 Server tower ...

1 Answer

Need to increase the hdd size in a dell poweredge 1600sc with raid 1

You will not be able to increase the hdd size of a raid array, it's size is set. If you need more storage, you can add additional drives ( either in raid or standalone ) and use the new drive(s) for storage, but the original array will remain unchanged. The other option is to back up all of your data, install new drives and create a new array.

Feb 10, 2011 | Dell PowerEdge 1600SC Server

1 Answer

Enable RAID system

use this guide, this is fo the embedded sata raid controller that comes standar with the ml150 g5.

Enabling SATA RAID functionality in the BIOS Setup Utility: 1.Boot the server, and then press F10 to enter the ROM-Based Setup Utility (RBSU).
2.Go to the advanced tab.
3.Enter the IDE configuration or hard disk configuration.
4.Change the ATA/IDE configuration to enhanced or SATA controller 2 enhanced (if not available then use enabled mode).
5.Configure SATA as RAID or configure controller 1 as RAID.
6.F10 to save and exit.
7.Reboot the server.
8.During post f8 will now show up for the embedded SATA set up.
•Creating the RAID volume.
1.Enter the embedded SATA setup by pressing f8 during post.
2.Enter the array configuration utility.
3.Enter create array.
4.Create the raid volume as desired.
5.Save and exit.

i hope it helps you!!!

Aug 11, 2010 | HP ProLiant ML150 G5 Server

1 Answer

Confuguring raid5


You would need 4 Hard disk drives in total. you would need to create 2 RAID 0 (striping) and then Mirror them (RAID 1). to elaborate, HDD A&B will be at RAID 0 as well as HDD C&D. after, you would have to Mirror your two RAID 0. (raid 0+1 is also known as raid 5)

Hope this helps.

Jul 09, 2010 | IBM x3400 Server

2 Answers

Raid 1

there must be some key on the startup to enter into the raid menu. And in that raid menu you can create raid .

Jun 23, 2009 | IBM x3400 Server

2 Answers

Problem with creating array

The Perc RAID controller in a 2600 doesn't support RAID 4.
You can do RAID 0, RAID 1 and RAID 5.

With 3 HDD's your best bet would be a RAID 5.

Mirroring is RAID 1 (which would only use 2 of the drives)

Aug 31, 2008 | Dell PowerEdge 2600 Server

1 Answer

Xseries 346 wont boot

You don't say whether or not your os is on the RAID 5 partition. Assuming that it is (for performance reasons, this is not recommended) then you should check to see if you have the option of configuring a separate raid configuration on your raid card (e.g. do you have a card with more then one RAID channel?) If this is so, I would create a separate RAID 1 array and install the OS just on that. Then you can mount the RAID 5 array with your data intact. Once you're up and running, you can remove the old OS partition, as it's no longer needed.

Apr 02, 2008 | IBM xSeries 346 Server

Not finding what you are looking for?
Intel Server Platform SPKA4 (SKOC2HI) Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computer Servers Experts

 Mike M
Mike M

Level 3 Expert

3320 Answers

Will Halftowaite

Level 3 Expert

503 Answers

Brett Duxbury
Brett Duxbury

Level 3 Expert

2659 Answers

Are you an Intel Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides