Question about Vehicle Parts & Accessories

2 Answers

Hi i have a spy car alarm can i get help to install it on a holden vx executive? thanks

Posted by on

  • 3 more comments 
  • m_m3911 Sep 26, 2009

    hi i just need to know the wiring. i have the alarm diagram and my cars body control module chart plus my car has a factory immobiliser and im not sure how to connect the alarm so what i need is a step by step guide on how to install this alarm on my car which is a holden vx

  • m_m3911 Sep 26, 2009

    hi can i get a step by step guide on how to install a remote start spy alarm on the holden vx executive 2002 thanks

  • m_m3911 Sep 26, 2009

    ill attach the alarm diagram but its bigger than 150kb so can i email it to you? plus is says it has a wire for immobiliser bypass. do you think it will work without disabling the factory one?

  • m_m3911 Sep 26, 2009

    first i need to know if my car has a factory immobiliser and the aftermarket alarm has a wire for immobiliser bypass can i install the alarm without disabling the factory immobiliser? thanks

  • m_m3911 Sep 26, 2009

    nice start

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 615 Answers

What do you need exactly? Do you need information on how to install it or a specific request? This is a standards instillations starting by looking for a suitable location for the alarm and providing direct hot connection from the battery using a fuse on that run and grounding the unit with a clean ground. See that you use a good wire and connection I recommend using the ones they use to install stereos the good one is blue color, you need to use different color to confuse anyone from looking for it to disconnected by using the stereo wires they will think it is for the radio and not alarm. I will be working with you to conclusions of this issue. Please see that grant me your approvals by rating my service and I hope that I can serve you again the future.

Posted on Sep 26, 2009

  • Norman Al-Anbar Sep 26, 2009

    you cannot use both at the same time so you need to disconnect the factory immobilizer

    and then do the standard instillation according to the diagram…if you need step by step you need to send me a copy of your alarm and I will create one for you that work on your car. Please see that grant me your approvals by rating my service and I hope that I can serve you again the future.

    let me know and I will post my address

  • Norman Al-Anbar Sep 26, 2009

    you cannot use both at the same time so you need to disconnect the factory immobilizer

    and then do the standard instillation according to the diagram…if you need step by step you need to send me a copy of your alarm and I will create one for you that work on your car. Please see that grant me your approvals by rating my service and I hope that I can serve you again the future.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 86 Answers

What is your specific question/problem with the install?

Posted on Sep 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What each colourvwiringis for in vx ,2002,Commodore


The Holden Commodore (VX) is an executive car that was produced by the Australian manufacturer Holden from 2000 to 2002. It was the second iteration of the third generation of this Australian made model. Its range included the luxury variants, Holden Berlina (VX) and Holden Calais (VX), and it formed the basis for a new generation Holden Ute (VU) coup? utility and Holden Monaro (V2) coup?.
The VX series was produced between October 2000 and September 2002, as a minor restyling update to the VT series from 1997. It introduced greater model differentiation along with gains in crash safety. An intermediate Series II was launched in August 2001, featuring a revised suspension system among other changes.

Thanks,

Landon

Apr 16, 2017 | Cars & Trucks

1 Answer

Trying to install replacement side passenger window in Holden Berlina 2002 VX II - not having much luck - any hints/tricks?


what exactly are you having trouble with? the fitting of the glass? removal of the trim to gain access?

Sep 13, 2016 | Holden Cars & Trucks

1 Answer

Hi - looking to fit a Mongoose MAP80 upgrade alarm to a 2011 Colorado dual cab - does anyone have wiring diagram or info for door trigger, arming/lock wire & disarming/unlock wire Thanks


Peter, This is what I found on google search, you can also try google search Mongoose MAP80 upgrade alarm wiring instruction as there is a lot more info. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www.mongoose.com.au/vehicle-installation-manuals/MAP80inst.pdf
http://www.mongoose.com.au/vehicle-wiring-holden/colorado_2009_2010.pdf

Aug 04, 2016 | 2005 Holden Rodeo

1 Answer

Check transmission trian on Vx commodore executive it had no fluid have filled it but keep getting that message is their a reset button


try this just commodores forum
on the VZ 2004-- 2006
Forum VZ Holden Commodore 2004 2006

I only know of engine service message
clearance using the mode buttons on a VT.VX

i hope you are a lucky person because
any commodore transmission man or auto
driven without fluid would have taken some internal damage






26223843-clxv5ap2upit2hrfgpiip3cn-3-0.jpg

Jun 23, 2016 | Cars & Trucks

1 Answer

Hi.month ago i install spy 5000 alarm.now the problem is ...cant start the bike because the alarm goes off always


Hi, Georgian read the manual provided in the link below you may need to do an alarm reset for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day
spy 5000m remote start problems ninjette org
How wired my spy 5000m to 2005 kawasaki zx10r
spy5000 alarm manual pdf
2008 2010 Kawasaki Ninja ZX 10R Service Manual Moto Data Project FREE!!!!!!

Jun 17, 2016 | 2010 kawasaki Ninja ZX 10R

1 Answer

How do you disable the seat belt warning chime?


Hi Sman, Why not just wear the belt? It is installed to keep you safe. Regards John

May 23, 2014 | 2006 Holden Commodore SS

3 Answers

Spy 5000m remote start issues


You need to adjust the tachometer sensing wire, it usually wraps around a spark plug wire so I can sense when the car starts. On my spy alarm, the wire was grey. Hope this helps.

May 05, 2010 | Brand Remote Start/keyless/car Alarm Very...

3 Answers

Holden vx commodore immobiliser


to fix the key you need a screw driver to pry the to halves of the key casing apart (make sure you have a spare set) taking care not to damage the internal electronic component board, because this electronic circuit board (cct bd) is powered by a 3 volt battery (which is also used to run the bios on computers) can be purchased for about 3 dollars from **** smiths, you need a small pair of side cutters to cut the metal tag connections between the battery and the cct bd taking care to note which is the positive and negative tracks on the cct bd, then using a soldering iron desolder the metal tag connections from the cct bd take care not to damage the copper tracks on the cct bd, try to use the proper desoldering technique (the copper gauze or a suction gun) to remove excess solder from the metal tags because they need to be removed, when the tags are removed from the cct bd there is a small hole on each copper track for the positive and negative reconnections to the newly purchased battery, use light audio speaker wire, black for negative and red for positive, presolder the wire ends first then cut the bear ends down and solder to the tracks taking care not to cross tracks with the solder, then shorten the both positive and negative lengths so the battery and the wires will fit back into the casing of the key and resolder the wire connections to the battery, before closing the key casing test the key to see if the immobiliser is operating then relocate the ring seal and close the two casing together with tape or reglue with arildite glue. if your soldering technique is not up to scratch practice your technique until you feel confident and this should save you about $100

Aug 02, 2008 | Graco Spree 511 Holden Travel System...

Not finding what you are looking for?
Vehicle Parts & Accessories Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vehicle Parts & Accessories Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14228 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...