Question about Canon PIXMA MP780 All-In-One InkJet Printer

Open Question

Replaced ink but mssg says 'cannot use cassette set paper in ASF'and letters won't print. It was printing fine until ran out of ink...and I put in new. Also, new yellow shows that it's almost out of ink!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Garfunkel01
  • 56 Answers

SOURCE: Pixma MP780 Printer, not printing

sometimes those measures of ink levels are not very accurate. actually they're usually rather far off... try a new cartridge Usually the easiest solution.

Posted on Aug 17, 2007

  • 359 Answers

SOURCE: PIXMA MP780 printing trouble

If you haven't done so, I would try another new cartridge. It is entirely possible (and occurs frequently) that you got a bad cartridge. Assuming you removed the tape from the cartridge before putting it in, this is generally indicative of either a bad cartridge, bad print head, or that heads or ink tanks may need cleaning.

The Canon support page for this printer is at:
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=238&modelid=10444

However, as Canon pages come up as generic pages (without the text I input for you), you will have to type in "missing black ink" (without quotes), to see the material they have posted in this regard. You will find instructions there in regard to how to clean the print heads, etc., if that is necessary. However, I would definitely try another cartridge first, especially if you haven't had that much use on the printer, such that you think these other measures may be necessary.

Please post back if you need further help, otherwise thanks for rating FixYa!

Posted on May 28, 2008

SOURCE: Cyan, magenta and yellow not print after replace the new print head

I am going back to Epson

Posted on Jul 25, 2008

  • 2 Answers

SOURCE: CANON MF4140 'LOAD CORRECT PAPER CASSETTE : LTR'

I had the same cr@p of the problem yesterday. The problem was not in the paper. You have to do 2 simple things, from which one will solve the problem.
first, download the latest drivers and install them.
And the more important thing, the problem occurred due to incorrect paper format. Solution is very simple. Open MS word or something similar, file->print.. and before you print open Properties menu. There for the Output Size will be selected "Match Page Size". you don't want that (i don't know why it doesn't work), but the solution is manually select A4, or whatever your page size is.

Posted on Dec 27, 2008

  • 2 Answers

SOURCE: CANON MF4140 'LOAD CORRECT PAPER CASSETTE : LTR'

I had the same cr@p of the problem yesterday. The problem was not inthe paper. You have to do 2 simple things, from which one will solvethe problem.
first, download the latest drivers and install them.
And the more important thing, the problem occurred due to incorrectpaper format. Solution is very simple. Open MS word or somethingsimilar, file->print.. and before you print open Properties menu.There for the Output Size will be selected "Match Page Size". you don'twant that (i don't know why it doesn't work), but the solution ismanually select A4, or whatever your page size is.
And there it is... printer starts throwing pages out like crazy :)))

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Green light flashes 7 times


LED Blinking in Orange/Green:

2 times: No paper. (ASF) [1000]; Set the paper in the ASF, and press the Resume/Cancel button.No CD-R tray. [1001]*1; Set the CD-R tray, and press the Resume/Cancel button.
No paper in the cassette. [1003]; Set the paper in the cassette, and press the Resume/Cancel button.

3 times: Paper jam. [1300]; Remove the jammed paper, and press the Resume/Cancel button.
Paper jam in the under guide. [1304]
Paper jam in the rear guide.[1303]
Front door closed. [1250]; Open the paper output tray.

4 times: No ink.[1601 / 1611 / 1612 / 1613]; Replace the empty ink tank(s), or press the Resume/Cancel button. Pressing the Resume/Cancelbutton will exit the error without ink tank replacement, however, ink may run out during printing.

5 times: The print head is not installed [1401], or it is not properly installed (EEPROM data of the print head is faulty) [1403 /1405]. Install the print head properly, and close the access cover. Or, with the print head installed, turn the printer off and on.

6 times: Inner cover open. [1841]*2; Close the inner cover, and press the Resume/Cancel button.
Inner cover open (during printing on paper). [1846]*2; Close the inner cover, and press the Resume/Cancel button.
CD-R tray guide closed (during CD-R printing).[1850 / 1855]*1; Open the CD-R tray guide, set the
CD-R tray properly, and press the Resume/Cancel button.
CD-R tray guide open (during printing to paper). [1851 /1856]*1; Close the CD-R tray guide, and press the Resume/Cancel button.

7 times:No CD-R or DVD-R. [1002] After setting a CD-R or DVD-R in the tray, set the tray in the tray guide, and press the Resume/Cancel button.

8 times: Warning: The waste ink absorber becomes almost full (approx. 95% of the maximum capacity). [1700]; Pressing the Resume/Cancel button will exit the error, and enable printing. The service call error, indicating the waste ink absorber is full, is likely to occur soon.
In repair servicing, replace the bottom case unit (QM2-1249), or the ink absorbers (QC1-4222 / 4223 / 4224 / 4263 / 4264 / 4864).

9 times: The connected digital camera or digital video camera does not support Camera Direct Printing. [2001]; After removing the cable between the camera and the printer, press the Resume/Cancel button, and
re-connect the cable.

10 times: Automatic duplex printing cannot be performed (paper size not supported). [1310]; Press the Resume/Cancel button to eject the paper being used at error occurrence. Printing will resume from on the front side of the next page.

11 times: Failed in automatic print head alignment. [2500]; Press the Resume/Cancel button, and after confirming the following, perform print head alignment again: - Set an appropriate type and size of paper (plain paper, A4 or letter). - Check that the nozzle check pattern is properly printed (all ink ejected, no faint printing). - Protect the paper output slot from exposure to excessive light.
Access cover open. [1200]; Close the access cover.



LED Blinking in Orange and Green Alternately, or Lit in Orange:

2 times: Carriage error [5100]
3 times: Paper feed error [6000]
4 times: Purge unit error [5C00]
5 times: ASF (cam) sensor error [5700]
6 times: Internal temperature error [5400]
7 times: Waste ink absorber full [5B00]
8 times: Print head temperature rise error [5200]
9 times: EEPROM error [6800]
11 times: Carriage lift mechanism error [5110]
12 times: AP position error [6A00]
13 times: Paper feed position error [6B00]
14 times: Paper feed cam sensor error [6B10]
15 times: USB Host VBUS overcurrent [9000]
16 times: Valve sensor error [6C00]
17 times: Motor driver error [6D00]
20 times: Other hardware error [6500]
Continuous alternate blinking: rom error

Aug 31, 2014 | Canon PIXMA iP2000

1 Answer

My canon pixma ip2000 lights flashing 7 times


LED Blinking in Orange:

2 times: No paper. (ASF) [1000]; Set the paper in the ASF, and press the Resume/Cancel button.No CD-R tray. [1001]*1; Set the CD-R tray, and press the Resume/Cancel button.
No paper in the cassette. [1003]; Set the paper in the cassette, and press the Resume/Cancel button.

3 times: Paper jam. [1300]; Remove the jammed paper, and press the Resume/Cancel button.
Paper jam in the under guide. [1304]
Paper jam in the rear guide.[1303]
Front door closed. [1250]; Open the paper output tray.

4 times: No ink.[1601 / 1611 / 1612 / 1613]; Replace the empty ink tank(s), or press the Resume/Cancel button. Pressing the Resume/Cancelbutton will exit the error without ink tank replacement, however, ink may run out during printing.

5 times: The print head is not installed [1401], or it is not properly installed (EEPROM data of the print head is faulty) [1403 /1405]. Install the print head properly, and close the access cover. Or, with the print head installed, turn the printer off and on.

6 times: Inner cover open. [1841]*2; Close the inner cover, and press the Resume/Cancel button.
Inner cover open (during printing on paper). [1846]*2; Close the inner cover, and press the Resume/Cancel button.
CD-R tray guide closed (during CD-R printing).[1850 / 1855]*1; Open the CD-R tray guide, set the
CD-R tray properly, and press the Resume/Cancel button.
CD-R tray guide open (during printing to paper). [1851 /1856]*1; Close the CD-R tray guide, and press the Resume/Cancel button.

7 times:No CD-R or DVD-R. [1002] After setting a CD-R or DVD-R in the tray, set the tray in the tray guide, and press the Resume/Cancel button.

8 times: Warning: The waste ink absorber becomes almost full (approx. 95% of the maximum capacity). [1700]; Pressing the Resume/Cancel button will exit the error, and enable printing. The service call error, indicating the waste ink absorber is full, is likely to occur soon.
In repair servicing, replace the bottom case unit (QM2-1249), or the ink absorbers (QC1-4222 / 4223 / 4224 / 4263 / 4264 / 4864).

9 times: The connected digital camera or digital video camera does not support Camera Direct Printing. [2001]; After removing the cable between the camera and the printer, press the Resume/Cancel button, and
re-connect the cable.

10 times: Automatic duplex printing cannot be performed (paper size not supported). [1310]; Press the Resume/Cancel button to eject the paper being used at error occurrence. Printing will resume from on the front side of the next page.

11 times: Failed in automatic print head alignment. [2500]; Press the Resume/Cancel button, and after confirming the following, perform print head alignment again: - Set an appropriate type and size of paper (plain paper, A4 or letter). - Check that the nozzle check pattern is properly printed (all ink ejected, no faint printing). - Protect the paper output slot from exposure to excessive light.
Access cover open. [1200]; Close the access cover.



LED Blinking in Orange and Green Alternately, or Lit in Orange:

2 times: Carriage error [5100]
3 times: Paper feed error [6000]
4 times: Purge unit error [5C00]
5 times: ASF (cam) sensor error [5700]
6 times: Internal temperature error [5400]
7 times: Waste ink absorber full [5B00]
8 times: Print head temperature rise error [5200]
9 times: EEPROM error [6800]
11 times: Carriage lift mechanism error [5110]
12 times: AP position error [6A00]
13 times: Paper feed position error [6B00]
14 times: Paper feed cam sensor error [6B10]
15 times: USB Host VBUS overcurrent [9000]
16 times: Valve sensor error [6C00]
17 times: Motor driver error [6D00]
20 times: Other hardware error [6500]
Continuous alternate blinking: rom error

Aug 31, 2014 | Canon PIXMA iP2000

1 Answer

Hi, How to change default settings from auto to always print ltr? Thanks


You can program the copier to just print from the letter tray by choosing the letter cassette on the display and then immediately hit the additional functions key....select copy settings and scroll through until you see the store current settings option which will make it default to the letter cassette every time. Try to do an internet search for the ir2200 operators manual. A lot of the time the book is available for free download and the customer settings are outlined in great detail in that book. Good luck.

Jul 26, 2012 | Canon imageRUNNER 2200

2 Answers

My Canon mp600 was printing a photo when the error message "paper jammed" came up. I know the paper is in the machine, though I can't find it.What do you suggest?


You can access Canon online support info here. Enter paper jam as a search, then choose #4 to remove the obstruction.
Also see this:
Issue: Paper is jammed inside the printer
Solution: Removing paper jams MP600

Removing Obstructions or Jammed Paper If [Paper output slot - The paper is jammed. Clear the paper and press OK] appears on the LCD, follow this procedure to clear the paper jam Clearing paper jams from the auto sheet feeder (ASF) or paper output slot
Clearing paper jams inside the printer
Clearing credit card-sized or 4" x 6" paper jammed inside the printer

ASF / Paper Output Slot
  1. Turn off the printer.

  2. Remove paper from the ASF.

  3. Gently pull the jammed paper out.
    1. If paper is visible from the ASF, use both hands to pull the paper out slowly.
    2. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.

      The above illustration shows a PIXMA MP500.

  4. If the paper tears and a piece of that remains inside the printer, open the scanning unit (printer cover) and remove the paper from inside the printer.

    Note:
    Be careful not to touch the components inside the printer.


  5. Turn on the printer and confirm that the Alarm light is off.
    (If the jammed paper remains in the printer, the paper may be automatically ejected.)

  6. Load paper back into the ASF.

  7. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top
Paper jams inside the printer
  1. Turn off the printer and disconnect the power cord and USB cable.

  2. Remove the jammed paper slowly using the following procedure.
    1. Open the rear cover to check if the paper is jammed.

    2. Pull out the cassette and check if the paper is jammed inside the cassette area.

    3. Stand the printer with the left side down, holding the document cover.
    4. Press the tabs together and pull the green cover toward you.
    5. Check if the paper is jammed.
      (If you were not doing Duplex printing, you do not have to follow this procedure.)

    6. Close the green cover and place the printer back to a normal position.
  3. Reconnect the power cord and power on the printer. Confirm the Alarm light is off.

  4. Load paper back into the ASF or cassette.

  5. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top

Clearing credit card-sized paper jammed inside the printer
Credit card-sized and 4" x 6" sized paper must be loaded properly. If this media is not loaded properly, it will feed into the printer and will not exit. Credit card-sized paper should only be loaded in the ASF and in portrait orientation. 4" x 6" sized paper can be loaded in the ASF or cassette. But must be loaded portrait orientation.
If credit card-sized paper was loaded in landscape orientation in the ASF and did not eject (exit), please follow this procedure.
  1. Turn off the printer.

  2. Load the same paper type that is jammed inside the printer in portrait orientation.

  3. Power on the printer.
    The paper stock in the ASF will automatically feed the jammed paper from the printer.

  4. To resume printing, load the paper in portrait orientation.

If 4" x 6" sized paper was loaded in landscape orientation in the cassette and did not eject (exit), please follow this procedure.
  1. Turn off the printer.

  2. Open the rear cover.

  3. Fold in four a piece of letter-sized plain paper.

  4. Push in the folded paper until it hits the jammed paper.

  5. If the jammed paper is visible from inside the printer area, pull it out and proceed to step 7.

  6. If the jammed paper cannot be pulled out, push in the folder paper from the rear so the jammed paper is in between the feed rollers.

  7. Pull out the folded paper and close the rear cover.

  8. Power on the printer and confirm that the Alarm light is off.
    The jammed paper should automatically eject.

  9. To resume printing, load the paper in portrait orientation.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks

Nov 17, 2010 | Canon PIXMA MP600 all-In-One InkJet...

1 Answer

No Printed documents


Have you performed a print head cleaning? If not, follow the instructions below:

1) Press <Menu> on the panel repeatedly until [Maintenance] appears on the display

2) Press left or right arrow buttons until the cleaning setting you want appears, either [Head Cleaning] or [Head Refreshing]

3) Press the <OK> button.

Note: Head cleaning should be attempted first, and may need to be done more than once. Examine the results of the test page.

Head refreshing is more aggressive, uses more ink and should only be performed when necessary (ie. when multiple head cleanings failed to solve your print problem).

Dec 20, 2009 | Canon PIXMA MP780 All-In-One InkJet...

1 Answer

Streaks on copy


Try these steps first:

1. Check ink level.


2. Nozzle Check Pattern
  1. Load A4- or letter-size plain paper in the Auto Sheet Feeder (ASF) or cassette.

  2. Press the <Feed Switch> button to select the appropriate paper source.

  3. Press <Menu> repeatedly until [MAINTENANCE] appears.

  4. Press <OK>.
    The machine prints a nozzle check pattern.

    bde48f2.jpg

  5. Confirm the pattern is not broken, missing, or a specific color is not printed.



3. Print Head Cleaning / Head Refreshing If the printed Nozzle Check Pattern is broken, missing, or a specific color is not printed, clean the print head.
  1. Press the <Menu> button on the printers operation panel repeatedly until [MAINTENANCE] appears in the LCD.

  2. Press the left [<] or right [>] arrow buttons to select the cleaning setting you want. Select [HEAD CLEANING] or [HEAD REFRESHING] for deep print head cleaning.

    Note: [HEAD REFRESHING] uses more ink than [HEAD CLEANING], so perform [HEAD REFRESHING] only when necessary.

  3. Press the <OK> button.

  4. Print a Nozzle Check Pattern and perform at least two Head Refreshings if the pattern is not correct.


You can also try using a higher quality print settings as follows:

Change the Print Quality Settings (Windows) The Quality setting controls how finely ink droplets are placed on the printed page. Depending on the type of paper being used a higher Print Quality setting does not always insure a better print. Print speed will decrease as the Print Quality setting is increased. Follow the instructions below to change the print quality settings in the Canon printer driver for the Windows operating system through a printing application.
  1. Click 'Properties' in the Print dialog box.

    Note: Depending on the Application software, 'Properties' may be displayed as 'Preferences'.

  2. Set the desired print quality in the 'Print Quality' section.

  3. Select 'High', 'Standard', or 'Draft / Fast'.
To set more detailed print quality settings, follow this procedure:
  1. Select 'Custom' and click 'Set'.

    cc8d5b7.jpg

  2. In the Set Print Quality dialog drag the slide bar from 'Fast' to 'Fine' to select the print quality.

    1bbaaa1.jpg

    Note: There are five options in 'Quality'. However, selectable options are limited depending on the media type.

  3. Select 'Auto', 'Dither', or 'Diffusion' from the 'Halftoning' section.


If the above steps do not solve your problem, it may be a time to purchase a new printhead.



Oct 09, 2009 | Canon PIXMA MP750 All-In-One InkJet...

1 Answer

I had a paper jam and got the paper out but still shows E2


E2-2 = No paper (ASF)
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error (bagian cleaning head)
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = ink absorber full or platen waste ink absorber full > reset dengan toolsnya
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
which error message exactly your printe show?

Sep 13, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Paper jam


You can access Canon online support info here. Enter paper jam as a search, then choose #4 to remove the obstruction.
Also see this:
Issue: Paper is jammed inside the printer
Solution: Removing paper jams MP600

Removing Obstructions or Jammed Paper If [Paper output slot - The paper is jammed. Clear the paper and press OK] appears on the LCD, follow this procedure to clear the paper jam Clearing paper jams from the auto sheet feeder (ASF) or paper output slot
Clearing paper jams inside the printer
Clearing credit card-sized or 4" x 6" paper jammed inside the printer

ASF / Paper Output Slot
  1. Turn off the printer.

  2. Remove paper from the ASF.

  3. Gently pull the jammed paper out.
    1. If paper is visible from the ASF, use both hands to pull the paper out slowly.
    2. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.

      05sj00147_03.jpg
      The above illustration shows a PIXMA MP500.

  4. If the paper tears and a piece of that remains inside the printer, open the scanning unit (printer cover) and remove the paper from inside the printer.

    Note:
    Be careful not to touch the components inside the printer.


  5. Turn on the printer and confirm that the Alarm light is off.
    (If the jammed paper remains in the printer, the paper may be automatically ejected.)

  6. Load paper back into the ASF.

  7. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top
Paper jams inside the printer
  1. Turn off the printer and disconnect the power cord and USB cable.

  2. Remove the jammed paper slowly using the following procedure.
    1. Open the rear cover to check if the paper is jammed.

      05sj00147_04.jpg
    2. Pull out the cassette and check if the paper is jammed inside the cassette area.

      05sj00147_05.jpg
    3. Stand the printer with the left side down, holding the document cover.
    4. Press the tabs together and pull the green cover toward you.
    5. Check if the paper is jammed.
      (If you were not doing Duplex printing, you do not have to follow this procedure.)

      mp600_bottomcover.gif

    6. Close the green cover and place the printer back to a normal position.
  3. Reconnect the power cord and power on the printer. Confirm the Alarm light is off.

  4. Load paper back into the ASF or cassette.

  5. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top

Clearing credit card-sized paper jammed inside the printer
Credit card-sized and 4" x 6" sized paper must be loaded properly. If this media is not loaded properly, it will feed into the printer and will not exit. Credit card-sized paper should only be loaded in the ASF and in portrait orientation. 4" x 6" sized paper can be loaded in the ASF or cassette. But must be loaded portrait orientation.
If credit card-sized paper was loaded in landscape orientation in the ASF and did not eject (exit), please follow this procedure.
  1. Turn off the printer.

  2. Load the same paper type that is jammed inside the printer in portrait orientation.

    05sj00147_01.jpg

  3. Power on the printer.
    The paper stock in the ASF will automatically feed the jammed paper from the printer.

  4. To resume printing, load the paper in portrait orientation.

If 4" x 6" sized paper was loaded in landscape orientation in the cassette and did not eject (exit), please follow this procedure.
  1. Turn off the printer.

  2. Open the rear cover.

  3. Fold in four a piece of letter-sized plain paper.

  4. Push in the folded paper until it hits the jammed paper.

    05sj00147_02.jpg

  5. If the jammed paper is visible from inside the printer area, pull it out and proceed to step 7.

  6. If the jammed paper cannot be pulled out, push in the folder paper from the rear so the jammed paper is in between the feed rollers.

  7. Pull out the folded paper and close the rear cover.

  8. Power on the printer and confirm that the Alarm light is off.
    The jammed paper should automatically eject.

  9. To resume printing, load the paper in portrait orientation.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Jun 22, 2009 | Canon PIXMA MP600 all-In-One InkJet...

1 Answer

5110 ERROR ON PIXMA PRO 9000


Solution: Press ON/OFF switch to reset the multifunction device

Reset the device when it is not functioning properly. If the device is not functioning properly or to clear memory, reset it.
  1. On the operator panel, press and hold the <ON/OFF> button for one second. (The display will go blank.)

    Note: It may be necessary to unplug the power cord if pressing the ON/OFF button does not shut off the printer.

  2. Wait approximately ten seconds and then press the <ON/OFF> button again.

  3. Wait until the device has completed its cycling process before submitting another job request.
Solution: Removing paper jams MP800R / MP830 / MP530

Removing Obstructions or Jammed Paper If [Paper output slot - The paper is jammed. Clear the paper and press OK] appears on the LCD, follow this procedure to clear the paper jam Clearing paper jams from the auto sheet feeder (ASF) or paper output slot
Clearing paper jams inside the printer
Clearing credit card-sized or 4" x 6" paper jammed inside the printer
ASF / Paper Output Slot
  1. Turn off the printer.

  2. Remove paper from the ASF.

  3. Gently pull the jammed paper out.
  1. If paper is visible from the ASF, use both hands to pull the paper out slowly.
  2. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.

    05sj00147_03.jpg

  1. If the paper tears and a piece of that remains inside the printer, open the scanning unit (printer cover) and remove the paper from inside the printer.

    Note: Be careful not to touch the components inside the printer.

  2. Turn on the printer and confirm that the Alarm light is off.
    (If the jammed paper remains in the printer, the paper may be automatically ejected.)

  3. Load paper back into the ASF.

  4. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.

Top

Paper jams inside the printer
  1. Turn off the printer and disconnect the power cord and USB cable.

  2. Remove the jammed paper slowly using the following procedure.

  3. Open the rear cover to check if the paper is jammed.

    05sj00147_04.jpg

  4. Pull out the cassette and check if the paper is jammed inside the cassette area.

    05sj00147_05.jpg

  5. Stand the printer with the rear side down, holding the document cover.

  6. Press the tabs together and pull the green cover toward you.

  7. Check if the paper is jammed.
    (If you were not doing Duplex printing, you do not have to follow this procedure.)

    05sj00147_06.jpg

  8. Close the green cover and place the printer back to a normal position.

  9. Reconnect the power cord and power on the printer. Confirm the Alarm light is off.

  10. Load paper back into the ASF or cassette.

  11. Press <OK> to clear the message and continue printing. If you are printing from an application software, follow the instructions displayed on your computer.
Top

Clearing credit card-sized paper jammed inside the printer
Credit card-sized and 4" x 6" sized paper must be loaded properly. If this media is not loaded properly, it will feed into the printer and will not exit. Credit card-sized paper should only be loaded in the ASF and in portrait orientation. 4" x 6" sized paper can be loaded in the ASF or cassette. But must be loaded portrait orientation.
If credit card-sized paper was loaded in landscape orientation in the ASF and did not eject (exit), please follow this procedure.
  1. Turn off the printer.

  2. Load the same paper type that is jammed inside the printer in portrait orientation.

    05sj00147_01.jpg

  3. Power on the printer.
    The paper stock in the ASF will automatically feed the jammed paper from the printer.

  4. To resume printing, load the paper in portrait orientation.

If 4" x 6" sized paper was loaded in landscape orientation in the cassette and did not eject (exit), please follow this procedure.
  1. Turn off the printer.

  2. Open the rear cover.

  3. Fold in four a piece of letter-sized plain paper.

  4. Push in the folded paper until it hits the jammed paper.

    05sj00147_02.jpg

  5. If the jammed paper is visible from inside the printer area, pull it out and proceed to step 7.

  6. If the jammed paper cannot be pulled out, push in the folder paper from the rear so the jammed paper is in between the feed rollers.

  7. Pull out the folded paper and close the rear cover.

  8. Power on the printer and confirm that the Alarm light is off.
    The jammed paper should automatically eject.

  9. To resume printing, load the paper in portrait orientation.
Thanks

Thiru

Jun 17, 2009 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

Error Message 5C00


4 times is usually Automatic print head alignment
Set a sheet of plain paper (A4 or letter) in the ASF.and adjust.

Jan 14, 2008 | Canon PIXMA iP8500 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA MP780 All-In-One InkJet Printer Logo

631 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1973 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...