Question about Malber P21 Front Load Washer

1 Answer

Water fills in and out during the whole cycle but no spin

So i normally put this machine into orange spin cycle twice to make sure that the cleaning products wont still be on the clothes. i saw the button extra rinse so i turned on the machine, turned the dial to the orange spin cycle, and pressed th button extra rinse. now the machine won't spin. the belt is on properly and i dun see a button to reset anyway. if pushing the reset button is the solution, canu plz tell me where the button is located?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 262 Answers
Re: water fills in and out during the whole cycle but no...

Unplug the machine for 60 sec or more then plug back in this may help this resets the computer good luck

Posted on Dec 17, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Washer fills with water during spin cycle

Go to and have model number ready. They have videos how to check it

Mar 02, 2015 | Samsung WA422PRHDWR 4.2 cu. ft Large...

1 Answer

Washer won t fill water

pipes maybe clear but is your area wher you live prone to limescaling? where the water pipe/pipes go into the machine there is a switch to shut on/off the flow of water during whatever cycle you want.this might be blocked or sticking. first try to select different cycles and see if any of those fills the machine with water. if no water comes its one of two things. that switch is faulty or communication between the switch and the front consule is at fault.
contact your supplier after trying to go thru a few different cycles.

Dec 04, 2013 | Frigidaire Washing Machines

1 Answer

Ge washing machine fills up with water on spin cycle

Sounds like the timer is screwed... Sending out the wrong signals and the dryer is doing the rinse cycle when it should just be the spin cycle. Do t know what your timer looks like in that washer but most now days look like the picture. 11_11_2013_2_52_52_am.png

Aug 16, 2013 | Washing Machines

1 Answer

Puddling on floor during high speed spin cycle

you have a leak in your outlet hose normally caused by rubbing on the drum barrel / repair with tape or replace whole hose but this brand of wASHER ITS VERY HARD TO REPLACE IF DONT KNOW HOW TO

Apr 27, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Machine fills too slowly and continues to fill in whole cycle

Remove the water filler hoses at the machine and test the flow of each one. If very slow, check the inlet screens on the faucet ends for plugging and make sure the faucets furnish full flow. The hoses themselves can sometimes become restricting of flow--replace them if so. Next, check the inlet solenoids on the machine for proper flow and shutoff when the power to them is stopped. They may or may not be cleanable--replace them if they are trouble. Hope this helps!

Jan 10, 2010 | Admiral AW22 Top Load Washer

1 Answer

Model GHW910PWO shuts down during the rinse,spin cycle

First, pressing cancel twice should clear the error code and it should restart when you press start. Then you can press cancel to stop the whole thing This should also unlock it. Unplugging it for a long while may also clear the code and unlock the door, not sure. 
the F-9 says it is an overflow condition and may need to be serviced. The F-11 says there is a serial communication error.This might be the case if the pump is running overtime due to clogging. 

To check if the filter is clogged, open the front panel, put a bucket in front of the unit, unseat the rubber feet holding in the white plug,  pull the white plug out so when you unscrew it, any water will run into the bucket, then unscrew it and clean the filter. screw the filter back in, set the white plug back into the unit, being sure to secure it with the rubber feet. 
As for it stopping, you may be filling it too heavy and the motor stopped if it over heated? 

Apr 23, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore HE4T washer won't rinse. Valves open to

An HF Code is a Water Inlet Problem- No or Insufficient Water Supply.

Press Pause/Cancel twice to cancel the cycle. Then, unplug the washer.

Run down the list again:
Make sure faucets are completely turned on.
Make sure the fill vavles (screens where water enter machine) aren't clogged.
Make sure the hoses aren't kinked, etc.

Plug the machine back in. Try another cycle. If the problem still occurs, You may need to replace your Water Fill Valve. Let me know if you need any further assistance.

Feb 23, 2009 | Kenmore Elite 45986 Front Load Washer

2 Answers

GE Profile washer won't spin cloths after wash or rinse cycle

My GE washer model number WLSR2000G3WW washes and pumps water out but will not spin...can someone help me to solve my problem PLEASE?

Jan 23, 2009 | GE WBSR3140DW Top Load Washer

1 Answer

Washer fills slow only in the rinse cycle

ck and clean screens first both sides be sure hoses are not reversed timer has no affect on fill rate if screens are clean replace valve

Sep 19, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Shows "LE" in display.

Machine has a bad motor or "stator" on this machine. It is a direct drive winding on the back of the machine. Remove the back panel, the one bolt removes the rotor then you will see the stator winding, replace it and your good to go.

May 11, 2008 | Washing Machines

Not finding what you are looking for?
Malber P21 Front Load Washer Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Malber Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jason Harris
Jason Harris

Level 2 Expert

256 Answers

Are you a Malber Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides