Question about A D S DVD Xpress DX2

1 Answer

Have ADS DVDXpressDX2 which worked before but not now.

Have ADS DVDXpressDX2 which worked before but now I get no sound after 6 minutes and 11 seconds of playback from file or dvd. I have recorded from a VCR and DVD player through DVDXpressDX2 box with same problem. I purchased a new sound card but didn't help. In another post other person has same problem so do not believe problem is in motherboard.

Posted by on

  • Harry Cello Jan 12, 2010

    I contacted ADS and their reply was to buy new software, which I did and have done several conversions to DVD from the camcorder and PAL system vcr through the ADS box. ADS tech reply came across that they were not going to work on the problem.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I had the same problem but changed the input from DV/DVD to VCR/TV. Worked for me. Hope this helps.

Posted on Jan 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The front facing camera of my new nextbook flexx 11 will not work, locks up. rear facing camera works fine.


Try a factory reset which will scrub it clean and reload Windows. Unfortunately, it seems to be a known issue. See below the reinstall link.

How to ? Restore Reset a Nextbook Flexx 11 to Factory ... www.youtube.com/watch?v=hPzTlywdsSM
  • BY CELLULARPROZ
  • 8 MIN
  • 8.1K VIEWS
2016-01-29 · Video embedded · How to ? Restore Reset a Nextbook Flexx 11 to Factory Settings ? Windows 10 ... on a Nextbook Flexx 11 Laptop ... Nextbook Flexx 11 windows ...
===============================================

  • I have a Nextbook Flexx 11 and my webcam isn't working and ... answers.microsoft.com/en-us/windows/forum/windows_10-other...
    • 7 TOTAL ANSWERS
    2015-08-05 · I have a Nextbook Flexx 11 and my webcam isn't working ... with my nextbook. it was ... found that both the front and back cameras do not work ...
  • my camera in my nextbook is blank. it wont work. help ... answers.microsoft.com/en-us/windows/forum/windows8_1-hardware/my...
    • 1 TOTAL ANSWER
    my camera in my nextbook is blank. it wont work. help DE. ... I understand that you are experiencing problem with camera not working in nextbook.
  • Welcome to Nextbookusa.com https://www.nextbookusa.com/productdetail.php?product_id=23 ... the Nextbook Flexx 11 tablet is the ... 11 delivers great image quality to read, work, ... Front/Rear Camera. The Nextbook Flexx 11 features a ...
  • Related searches for nextbook flexx 11 front camera not working
  • Nextbook Flexx 11 USB and Camera Problems - Microsoft ... answers.microsoft.com/en-us/windows/forum/windows_10-hardware/...
    • 7 TOTAL ANSWERS
    2015-08-12 · Bought a brand new nextbook flexx 11 from ... Nextbook Flexx 11 USB and Camera Problems ... Only one I have yet to overcome is the camera not working.
  • Nextbook Flexx 11 USB and Camera Problems - Qnundrum qnundrum.com/question/1506976 Bought a brand new nextbook flexx 11 from Walmart, ... Nextbook Flexx 11 USB and Camera Problems. ... and nothing but a black screen on both front and back facing ...
  • Nextbook Flexx 11 Camera Not Working-Idyliq Search www.idyliq.com/q_Nextbook+Flexx+11+Camera+Not+Working Welcome to Nextbookusa.com... the Nextbook Flexx 11 tablet is the ... Touch-Screen Technology & Front/Rear Camera. The Nextbook Flexx 11 features a touch ...
  • Nextbook Flexx 11 Camera Not Working_Yaelp Search www.yaelp.com/s_Nextbook+Flexx+11+Camera+Not+Working Results for Nextbook Flexx 11 Camera Not Working: Also try: Ads: Next; Also try: Ads: ©2015 Results for Nextbook Flexx 11 Camera Not Working ...




  • Jul 02, 2016 | Cars & Trucks

    1 Answer

    Samsung 50" led un50h6350. The TV is about 18 months old and the picture went out, the audio and back light are working. I've replaced the t-con board and that didn't fix it. Someone please help!


    Samsung LED TV Screed goes blank periodically for 1 sec - Forums ...

    www.cnet.com > Forums > Samsung

    CNETJun 11, 2015 - Lately, my Samsung LED TV's screen will black out from 1 -2 seconds then come back. The TV has been ... The TV is about 6 months old. .... I've only notice this when I'm watching in HD. ... by Stlouib / January 13, 2012 11:18 PM PST ...Mine does the same thing - picture goes black for 1 - 2 seconds and then comes back. Samsung Series 3 (330), won't show any picture/no sound?
    Jun 11, 2015
    Samsung LCD TV LN32A330 power won't turn on
    Jun 11, 2015
    Black Line across Samsung 50" Plasma has appeared?
    Jun 11, 2015
    Samsung LED UN55B7100 turns off on its own.
    Jun 11, 2015
    More results from www.cnet.com

    Are there still capacitor problems with Samsung TVs?


    Dec 21, 2015 | Samsung Televison & Video

    3 Answers

    Where is the body control module located in 2002 gmc envoy?


    It's under your back seat. See here for picture http://www.ebay.com/itm/like/261068608953?lpid=82
    Here is the relearn procedure which you have to perform so the new BCM will recognize your key and start the car:
    For those vehicles that use a BCM, the BCM can learn the resistance value of the existing key by using the relearn process. In order for the vehicle to start, the BCM (as well as the Passkey module in other vehicles) must identify the resistor pellet in the key, then the BCM sends a password to the PCM. If this password matches the password stored in the PCM, the system enables fuel delivery. So you can see that if either the BCM or PCM are replaced, a relearn procedure is necessary. This same relearn procedure can be used if an ignition key with a different resistance value is used to replace the existing key. Before beginning the relearn, make sure there is a fully charged battery in the vehicle, and both the BCM and PCM are properly powered up and in communication with each other. Now you're ready to initiate the relearn procedure.

    1. First, insert the ignition key and turn the ignition switchto the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
    2. Turn the ignition switchoff for 30 seconds.
    3. Turn the ignition switchto the "On" position (as in step #1) for 11 minutes again.
    4. Turn the ignition switchoff for another 30 seconds.
    5. Turn the ignition switchto the "On" position for 11 minutes a third time.
    6. Turn the ignition switchoff for 30 seconds one final time.
    7. Turn the ignition switchto the "On" position one final time and wait 30 seconds.
    8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, check for trouble codes and address them before attempting the relearn procedure again.
    You can pick one oif these up for $20 or less at a junkyard. For those vehicles that use a BCM, the BCM can learn the resistance value of the existing key by using the relearn process. In order for the vehicle to start, the BCM (as well as the Passkey module in other vehicles) must identify the resistor pellet in the key, then the BCM sends a password to the PCM. If this password matches the password stored in the PCM, the system enables fuel delivery. So you can see that if either the BCM or PCM are replaced, a relearn procedure is necessary. This same relearn procedure can be used if an ignition key with a different resistance value is used to replace the existing key. Before beginning the relearn, make sure there is a fully charged battery in the vehicle, and both the BCM and PCM are properly powered up and in communication with each other. Now you're ready to initiate the relearn procedure.

    1. First, insert the ignition key and turn the ignition switchto the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
    2. Turn the ignition switchoff for 30 seconds.
    3. Turn the ignition switchto the "On" position (as in step #1) for 11 minutes again.
    4. Turn the ignition switchoff for another 30 seconds.
    5. Turn the ignition switchto the "On" position for 11 minutes a third time.
    6. Turn the ignition switchoff for 30 seconds one final time.
    7. Turn the ignition switchto the "On" position one final time and wait 30 seconds.
    8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, check for trouble codes and address them before attempting the relearn procedure again.

    Dec 13, 2014 | 2002 GMC Envoy

    2 Answers

    I have a 11 year-old york diamond 80 furnace. The flame sensor lights up and ignite the flame for about 5-6 seconds. Soon the flame goes out once again. There's this clicking sound that is heard every


    You need to clean the sensor with steel wool so its very clean check sensor connections . If it is still not working you could change sensor also check out the pressure switch .

    Jun 20, 2017 | Heating & Cooling

    1 Answer

    Working alone,Maria can complete a task in 100 minutes.Ann can complete the same job in 2 hours.They work together for 30 minutes when Liu,the new employee,joins and begin helping.They finish the job 20...


    Check my work, before you hand it in -- there could be some DELIBERATE errors in my fractions. :-)

    Marie takes 100 minutes for 1 job.
    Marie took 50 minutes for 1/2 job.

    Ann takes 120 minutes for 1 job.
    Ann took 30 minutes and did 1/4 job.
    Ann took 20 more minutes and did 1/6 job.

    Together Marie & Ann did 1/2 plus 1/4 plus 1/6 job in 50 minutes.
    Together Marie & Ann did 6/12 plus 3/12 plus 2/12 job in 50 minutes.
    Together Marie & Ann did 11/12 job in 50 minutes.

    Liu did the rest (1-(1/2+1/4+1/6)) job in 20 minutes.
    Liu did the rest (1-(4+3+2)/12) job in 20 minutes.
    Liu did the rest (1-9/12) in 20 minutes.
    Liu did the rest (1/4) in 20 minutes.
    Liu worked for 5 minutes.

    Sep 17, 2010 | Computers & Internet

    2 Answers

    Code 11 01 - Hot Water Heater Kicks Off


    if you have build up in the heat exchanger it will cause the unit to use more gas to heat your water, if the gas line isn't sized properly then your going to kick the error codes off. it sounds like you have two problems, first you have build up in your heat exchanger and it needs to be flushed and second you need to get a bigger gas line to it

    Aug 19, 2009 | Water Heaters

    2 Answers

    Sony SLV-SE820 VHS VCR


    Uh oh. If you have already unplugged this unit and allowed to reset after 5 minutes, it will be time for a service visit...accordianman

    Feb 11, 2008 | Sony SLV-SE820 VHS VCR

    Not finding what you are looking for?
    A D S DVD Xpress DX2 Logo

    Related Topics:

    345 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top A D S Televison & Video Experts

    The Knight
    The Knight

    Level 3 Expert

    74136 Answers

    Cindy Wells

    Level 3 Expert

    5102 Answers

    Electro Med Services...
    Electro Med Services...

    Level 3 Expert

    6694 Answers

    Are you an A D S Televison and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...