Question about Zanussi FJS1225W Front Load Washer
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
it was the bearings, and a new machine was purchased in light of the cost of prts and repair against the age of the machine and the offers availiable in the january sales.
I have come to the conclusion buy an average machine just have the standard guaranteee if the machine dies replace it dont waste time and money with costly unnecessary repairs on any machine over 3 years old
Posted on Jan 28, 2008
Here's the instructions you need to replace the door bellow on a Whirlpool Duet:
Let me know if you need further assistance. I hope this helps you.
PS I know it's a lengthy read, but it's a simple repair if you follow the directions.
Posted on Jun 03, 2008
Check the water inlet valve/ Remove the water supply hoses and check the small screens inside the water inlet valve. Make sure they are free of rust or debris. The small screens tend to get rusty due to elements in the water and can cause the type situation you describe. I will attach a photo for reference. Hope this helped and best wishes.
Posted on Sep 04, 2009
Testimonial: "I greatly appreciate the input. It was quick and very precise in instruction. I know my husband will be impressed with me as well for contacting you"
Follow these steps to replace your door
For all Free appliance repair videos visit our VIDEO TUTORIALS
Disconnect all power to the machine first!!
1 Locate the outer clamp band securing the seal to the door rim on the washing machine and examine it carefully for holes or tears. Many can be prised off with a flat-bladed screwdriver they have a spring system holding them, but some have a tensioning arrangement that has to be loosened.
2 After removing the outer clamp band, locate the inner one securing the seal to the drum and establish how this is secured. It may be necessary to loosen a clip, or you may be able to prise the band off with a flat-bladed screwdriver. Some are like very large Jubilee clips that you have to undo usually from the top.
3 Once the clamp bands have been removed, use both hands to pull the seal away from the inner drum rim. Some machines have a water spout holes that will have to be lined up. Others have a drain holes.
4 Rubbing a drop of washing up liquid into the groove on the door seal/gasket that locates on the drum makes fitting the new seal easier.
5 the new washing machine door seal should be fitted by locating the drain holes at the bottom of the seal first then push it on with both hands working opposite directions towards the top. This is quite hard if you have never done it before.
6 refit the inner band remembering this must be tensioned correctly for it to be water tight.
7 now fit the outer band and the test the machine for any leaks,
All washing machine spares featured in this article are available at apart4u with more video help in our tutorial section.
Information provided is a guide only. aPart4u accepts no liability for any problems occurring whilst attempting any advice shown. If in any doubt about fixing your appliance, always contact a qualified repairer.
Posted on Jan 19, 2010
SOURCE: grey scum marking clothes
Power off the mains. The
filter is located behind the silver plate at the back of the machine at
bottom. Four screws hold it on. Drain
out all the water. The filter is inside
the big black rubber hose attached between the pump and the main drum.
the plastic clip holding it to the pump unit and then the metal cir clip
holding it to the main drum. Inside is a white molded cone and a big
which floats. You will find a lot of junk here, clean out thoroughly. To
put white cone back inside just as you found it, at the bottom, fit ball
into the cone. Attach to the bottom to the drum and re-fasten the cir
Finally reconnect the gator to the pump unit and tighten the plastic
clip. Check out the pump too before reconnecting.
And rate me nice pl for the free help!
Posted on Jun 08, 2010
Tips for a great answer:
Apr 19, 2014 | Maytag Neptune Washing Machines
Sep 22, 2008 | Frigidaire ATF6000ES Front Load Washer
Mar 11, 2013 | Washing Machines
Jan 10, 2018 | Samsung WF337AA Front Load Washer
Dec 01, 2010 | Dishwashers
Nov 27, 2010 | LG Dishwashers
Feb 09, 2010 | Hotpoint Aquarius WMA42 Front Load Washer
Oct 28, 2009 | Kenmore 44102 Front Load Washer
Jan 12, 2009 | Frigidaire ATF6000ES Front Load Washer
38 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: