Question about Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

My BF162 runs with the door open. I also cannot

My Hotpoint Dishwasher BF162 runs with the door open. I also cannot seem to change the programme as none of teh program lights come on. I suspect a faulty door catch but am not sure how to fix this . Any thoughts would be gratefully recieved

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Yup, could be that pesky door latch, or even the control panel board. This could be a case for a repair man or replacement, depending on the cost.

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint BF1620 Integrated dishwasher not working


Lets try the following hope this works

1.- unplug the appliance, isolate it from the electric supply.
2.- Remove the kitchen unit plinth and check inside the inspection panels below the door to see if there is water in the base.

If there is, sponge it out and then try the machine again.

Was this helpful?

May 07, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

The program light goes off and the BF162 doesn't start...


When you keep the button pressed for a few seconds the lights go off, this resets the dishwasher. Then press the p button again to the program you want 1st light is heavy soil 2nd light is normal soil, 3rd light is eco wash, 4th light is rinse. At the end of the cycle the program light you have selected will flash.

Apr 24, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

Hotpoint BF162............. Water left, not draining


Open the bottom panel of the washer and see if it is full of water, if it is drain it away and clean all of the filters inside the washer and reset.

Mar 04, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

Hotpoint bf162 built-in dishwasher error codes


take out diswasher, tip it backwards and drain out water. make sure that salt resovoir is on tight and there are no leaks from the arms

Jan 11, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

2 Answers

Problem selecting programme


hi
sounds like you have a heater problem,check connections on your main module behind control panel if all appear ok check you heater for open curcuit.

Apr 27, 2008 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

Belling IDW 603 dishwasher


You can cancel the programme at any point by holding down the last button on the right hand side for about 10 seconds until it clears (its the same button you use to get it going again when you open up the door).

Mar 05, 2008 | Belling 24 in. IDW603 Built-in Dishwasher

1 Answer

Hotpoint bf162


after the 20 seconds does it restart

Feb 25, 2008 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

Hotpoint bf162 built-in dishwasher error codes


2+4 - Heating circuit not working. Possible causes - Heating element, connections, timer relay.
Maybe too late a response.

Ian

Feb 10, 2008 | Hotpoint 23 in. BFI62 Built-in Dishwasher

3 Answers

BF162 Hotpoint intergrated dishwasher


consult manual under troubleshooting.
if no manual, or if it does not address this, consult service center.

one likely cause you can try first is to disconnect it from power via the cord or a breaker. after a brief period, it may reset itself.
otherwise you likely have a logic board issue.

logic boards seem to be very vulnerable in dishwasher environments. the type of issue you have is very common among most brands. don't feel alone.

good luck
mark

Dec 28, 2007 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

It's Leaking Water!


Most common reason is that the lower spray arm splits on the seem and sprays water under the door, to proove if it is this remove lower spray arm and run through program if no leak fit new arm. Regards Advisor

Aug 30, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Hotpoint 23 in. BFI62 Built-in Dishwasher Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

AcmeUK

Level 1 Expert

25 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...