Question about Xerox Phaser 7300DN Laser Printer

1 Answer

Xerox Phaser 7300

Printer powers up OK but screen freezes at opening and will not proceed to complete loading to the ready status.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 208 Answers

You need to go to theExecute a NVRAM Reset in Diagnostic Mode sceren and find service diagnostics and Execute a NVRAM Reset. You most likely have some software corruption that needs to be cleared.

Posted on Dec 20, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help with u2 code on phaser 7300


U2 is an engine EEPROM failure - you'll need to replace the main board to fix that, I'm afraid.

Jan 08, 2013 | Xerox Phaser 7300DN Laser Printer

1 Answer

I have a Xerox phaser 7300 that keeps telling me to install or reseat the black cartridge


It is slightly unusual for it to be the black toner cartridge (usually cyan or magenta) but this issue is quite common on the 7300. You can find a lot of information about this here.

Dec 15, 2010 | Xerox Phaser 7300DN Laser Printer

1 Answer

Colors do not align


Apparently, turning the unit off for 30 seconds, then back on will force the Phaser 7300 to do a color alignment procedure (according to Xerox support).

Then, if the problem persists, you are instructed to follow a very detailed troubleshooting procedure which I will leave with you in the following link:

Xerox Phaser 7300 Misregistration Issues

I hope this helps!

Nov 03, 2010 | Xerox Phaser 7300DN Laser Printer

2 Answers

Xerox phaser 7500DN does not proceed after warming up screen. Hangs on Warming Up Screen.


Open and close the paper drawers!!! Super stupid solution, but trust me... it works!

Aug 17, 2010 | Xerox Phaser 7750DN Laser Printer

1 Answer

I have a phaser 7300 that asks for a transfer unit about every 3 weeks. It prints good until it asks for unit and then it will not print until I install a new one. I am ready to install the 4th unit but...


I think you might have a Spring missing for the Waste Toner Full Sensor. The machine tolerates the sensor status for 2K pages and then shuts it down.

Truthfully, it is really hard to describe in a few sentences. It belongs in the frame wall under near where you have the white waste toner section of the Transfer Belt. This spring pushes a flag up that hits the Paper Entrance Sensor (yes, near the bypass tray)

The PN for the spring is 116-2050-00.

Whit
Item, Inc.

May 21, 2010 | Xerox Phaser 7300DN Laser Printer

2 Answers

Xerox Phaser 7300 color misregistration


Apparently, turning the unit off for 30 seconds, then back on will force the Phaser 7300 to do a color alignment procedure (according to Xerox support).

Then, if the problem persists, you are instructed to follow a very detailed troubleshooting procedure which I will leave with you in the following link:

Xerox Phaser 7300 Misregistration Issues

I hope this helps!

Mar 15, 2010 | Xerox Phaser 7300DN Laser Printer

2 Answers

False reading of toner cart status


Sounds to me like you actually have the wrong part number. There are more than one cartridge for the Xerox printers, They have different chips on them. One is for billable accounts, one or more than one for accounts that pay for prints. There also was as i remember a spring type clip they left off some cartridges.
So with what you have tried and the old cartridges work fine, strongly suspect bad carridges.

Dec 01, 2008 | Xerox Phaser 7300DN Laser Printer

2 Answers

Phaser 7300 Error Code/Message


Seems to be something to do with the Ram.

More help HERE

Jun 01, 2008 | Xerox Phaser 7300DN Laser Printer

1 Answer

7300 jam


I find that I only get paper jams when I don't have the correct paper selected, i.e. plain, light card, glossy. The printer really does expect you to have the right one selected on the screen as is loaded in the tray.

When you get a jam, carefully open the designated location and make sure you remove all pieces of the paper.

Apr 05, 2008 | Xerox Phaser 7300DN Laser Printer

Not finding what you are looking for?
Xerox Phaser 7300DN Laser Printer Logo

Related Topics:

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Michel

Level 2 Expert

97 Answers

Philip Hughes

Level 2 Expert

75 Answers

docukaaf

Level 1 Expert

25 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...