Question about Maytag Neptune FAV6800AW Top Load Washer

3 Answers

Looking for replacement bearings for the outer tub to inner tub on our Maytag FAV6800AWW, S/N 13389034ET. Don't want to replace the whole outer tub assy.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 29 Answers

Get the bearings here.

http://www.thebigbearingstore.com/index.html

Part numbers

6206-2RS
6207-2RS

You'll also need the seal kit.

These guys have them

http://www.pcappliancerepair.com/index.html

Part number

12002022

I'm not affiliated with either company. If you can find them elsewhere cheaper more power to you.

Maytag told me I had to buy the tub for around $700.

I am halfway through this repair on mine. I haven't ordered the parts yet.

All the parts should cost you around $60-$70 + shipping.

The bearings are very difficult to remove. Some douche online rents a tool for $400 deposit + like $150 rental fee. I pounded mine out with a metal rod. The tool would probably be easier.

Good luck.

Slatrom

Posted on Sep 28, 2009

  • Slatrom Sep 28, 2009

    For whoever it was that asked. Yes you need both bearings. One bearing goes in from the front (inside) the other goes in from the back. You have to pull out the drum which means you have to pull the front off the tub. You should be able to reuse the seal. If its distorted at the bottom, pull it off and turn it 180 degrees so the (distorted) bottom is at the top. Don't forget to remove the snap ring at the rear bearing! You must put the bearing spacer (between the two bearings) back in when you reinstall.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 335 Answers

It sounds like you may have to replace the Outer Tub to replace the Outer Tub bearing .....ain't that just peachy.....good job Maytag design team.

If you are the original owner I would press Maytag hard to replace the Outer Tub based on the Outer tub Bearing failure. Their warranty states third thru tenth year Drive Motor, Outer Tub and Sealed Transmission. I’m sure you will need to have a certified Maytag repair service tech certify the failure and fix action required. Why should an Outer Tub bearing replacement cost you $430. Another poor design issue of this machine.

Looking for replacement bearings for the outer tub - 4003728.jpg

Posted on Sep 26, 2009

  • 1 more comment 
  • dh1200s
    dh1200s Sep 28, 2009


    Slatrom

    Great info! After reading your post I did a quick search and found this post on outer tub bearing replacement see maj7th post of Jan 19, 2008 he mentions the 6207-2rs bearings. You mention the two different types of 6200 series bearings. Are there to different bearing types used in the FAV6800AW Outer Tub? Looks like maj7th just used the 6207-2RS that link is to ebay. Thank you for your info and you have my vote.

  • dh1200s
    dh1200s Sep 28, 2009


    Slatrom

    One more question is this the tool you used to remove the Spinner Nut 12002139 - Spinner Tool Kit, or is there some other tool?

  • dh1200s
    dh1200s Oct 02, 2009

    Hey chris_denise ,



    If you replace your outter bearings can you let mo know what bearing type. I'm not clear if the are two 6207-2RS used or one each

    6206-2RS, 6207-2RS. Also how did you remove the Spinner Nut? Di you purchase a special tool or 1.75" socket? I believe that is the Spinner Nut size.



    Tnx, Rich

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 220 Answers

There is no other way to replace the bearing,it is pressed into the tub at the factory,the seal you can get
but no one makes a bearing..

Posted on Sep 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible to take the bearings and seals out from pulley side of this crosley washer?


no it is not possible. The bearing is part of the rear outer tub. In order to replace it you must take out the whole tub assemble and disassemble it that way. Also be aware that these bearing often go when the inner tub assembly has cracked on its rear mounting bracket so you may be looking at replacing both pieces instead of just one.

Nov 15, 2012 | Washing Machines

1 Answer

Leaking at bottom of washer after it spins out not alot of water but a pain in the ****, how do you get in to the back of the washer?


The FAV6800A and FAV9800A only have access thru the front panel and washer top once released fromt the base......no rear or side access. See Pick of Outer Tub removed for Tub Seal and bearing replacement.

Google ""16022808.pdf"" to find the Service Manual.

Page 33 will show ou how to release the top cover and page 41 for front cover removal.

If you have wash water leaking down on the Clutch Pulley I feel you have a Tub Seal leak. The issues could be related to the drain hose/drain pump or cracked outer tub.

I don't troubleshoot on this forum to difficult to carry on thread. Google ""Neptune TL Washer FAV6800AWW"" or ""FAV6800A/FAV9800A Outer Tub bearing replacement"". Two DIY forums I frequent that I feel are true DIY forums.



fav6800awdiy_6.jpg

Sep 04, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Model fav6800aww drains during the wash and rinse cycle but does not drain during the spin cycle. it give an dc code during the spin cycle which i know that means unbalance but what does that have to do...


Clutch issue and possible time for a tub seal replacement

Google this for a post that covers the Clutch removal and inspection/repair;

""Neptune TL Washer FAV6800AWW"" you will find the Service Manual in post 5 of that sticky.

Google this for Outer Tub bearing rebuild;""
FAV6800A/FAV9800A Outer Tub bearing replacement""

Aug 20, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Can you replace the outer tub bearings on a Maytag Neptune Model FAV6800AWW


yes you can but will warn you it is a small project to do... the unit will require to be dismantled in order to get to the outer bearings... the lower unit taken apart and tub springs, drain hoses and taken out of machine to access everything... can be done but is about a 2 hour project if it is your first time to do it...

Jan 30, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

My Maytag Nuptune fav6800aww won't spin. I followed the directions to replace the clutch, but that didn't fix it. The tub will not rotate in either direction. I have taken the transmittion out and it...


Maybe the Outer Tub bearings are seized. With the Clutch Pulley removed the wash basket should rotate within the Outer Tub bearings with one finger in CCW and CW direction does it?


"" I followed the directions to replace the clutch, but that didn\'t fix it. "" Was it my post Clutch Fix post? If your FAV6800A used the Upper Bearing One-Way roller clutch bearing ring do you feel on reassembly the parts are seated correctly.


What are the first two digits of you s/n of your machine?


Was the Clutch Pulley One-Way Roller clutches bearing rusted up severely or only slightly? I'm trying to get a feel for a Tub Seal leak........Rich

Oct 05, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

I have a load squeaky sound on my FAV6800AWW washer. THe machine spin but when is starts agitating, the sqeaky sound can be heard.


This could be the start of Outer Tub Bearing issue.


Raise the lid of your washer and rotate the wash basket CCW as fast as you can. Does is spin down slowly to a gentle stop after several revolutions with no bearing noise?

The Service Manual for reference. Sears Parts Direct for reference.

I would by removing the Clutch Pulley and check for One-Way Roller clutches bearing wash water contamination. That will give you a feel for the integrity of the Tub Seal. See my Clutch Fix post for support.

If this is Outer Tub Bearing noise you will have to replace them along with the Tub Seal and Tranny O-ring. The Series 16 machine (I have that one also doesn’t use the upper Clutch bearing ring. That upper One-Way Roller clutches bearing is integrated into one of the Outer Tub bearings.

See this post. This guy bothered me for his statement that I left him hanging. I’m a DIY’er not a appliance tech and most AT’s won’t touch this with a 10 foot poll due to lack of knowledge. I did replace the Outer Tub bearings on a ebay win Series 10 machine. See this post for the details of that.

Don’t get too excited by any of this. 1st determine if the squeaky noise is Outer Tub bearing noise I haven’t had them fail yet but I would suspect you will hear metal against metal grinding of the ball bearings in the bearing race. There will be down time for the tear down and work. You need to determine if this is worth it for your situation. No more than a $85 to replace Outer Tub bearings tub seal tranny o-ring and buy Maytag Spinner Nut removal tool for reassembly and you extend the service life of your $1K machine.
If you want to DIY further let me know……Rich

Jun 12, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag washer MAV551EEWW top load with loose tub


If the tub seal lets go water will weep into the tub bearing. This will rust the basket shaft and normally wreck the tub bearing. Once the bearings starts to get worn enough it usually gets very noisy. The tub bearing is pressed onto the outer back half of the tub shell assembly. Normally need to replace the inner basket/shaft assembly  and the outer shell with the tub bearing. 
Sometimes the inner basket support will crack, this can give an clicking or banging noise as well.
 
Pictures of this job...
A sure indication was the brown junk/gookus leaking out if the rear bearing area and the belt has spewed it around in the drum that the rear bearing and seal was bad...
Picture1 - Picture2
The whole outer shell and basket come out to do this repair....what bad bearing and rusted shaft looked like...
Picture1 - Picture2 - Picture3
I had to remove the back panel. Undo the pump hose & water level hose, remove the 2 shocks, remove the motor, undo the front boot from the outer panel and remove the 2 springs to lift the whole assembly out from the back to work on it.
Picture1 ( boot pushed inside ) Help page1 - Help page2

May 07, 2009 | Washing Machines

1 Answer

Outer tub bearings are gone


My bearings went out too and I found this site http://www.neptunebearing.com/ Ordered the bearings and the Tony Tool. My son and I replaced the bearings in about 2 hours!

Apr 03, 2009 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Maytag Neptune FAV6800AW Top Load Washer Logo

1,269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...