Question about T-Mobile Dash Smartphone

1 Answer

Tmobile dash When replacing the screen on my dash there is a round metal piece attatched by two wires at the bottom of the phone. the wire was so brital it snapped. what does this piece controll. Do I need it? My keyboard now doesn't work so I'm assuming thats what it controls. thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

You need to get a phone for parts preferably one that has a broken lcd then switch out the parts you need.

Posted on Jun 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore washing machine not spinning


If this is a top loading machine; then the "Lid Switch " is broken. To get to the switch, UNPLUG THE POWER CORD, standing in front of the machine, there are trim strips on each end (left and right) of the "dash". To remove the strips pop them off starting at the top and pulling towards yourself. Once the trim strips are off you'll see a screw at the bottom of each corner. Remove the screws-KEEP THEM-. Now the dash will lift up and fold back out of the way. Now you should see a curved metal piece at each corner. Use a screw driver tip and remove them. Now you can lift the metal piece that is the top of the washer. Underneath and on the right side you will see the lid switch, unplug the wires and replace the switch. Plug the wires into the new switch and put it all back together.

Aug 29, 2014 | Kenmore Washing Machines

1 Answer

Dash guages and headlights dont work


Check the overdrive wire coming out of the bottom of the gear shift lever. My 98 Gr Mar. had a tiny burr in the wire there. You will need to remove the whole gear shift lever cover, the ignition key ( in order to get the top piece off) and the bottom metal plate under the plastic cover on the bottom of the steering column. This is all very simple and quite easy. Just go on line to find how simple it is to remove the key.The wire had a bare spot right near the bottom of the shift lever and all I did was electric tape it up!

Jul 24, 2013 | Cars & Trucks

1 Answer

Screen wont work on my tview d74ts in-dash touch screen


Is it wired correctly? Red wire to switched ignition accesory, such as the factory radio was? Yellow to battery? Are their fuses intact?

How about the ground wire? Or did you just secure that to the dash? If so, that metal piece may not have a ground connection to the body shell, or the engine.

Jun 01, 2012 | Car Audio & Video

1 Answer

Tmobile dash screen is white


Yes it causes probelm in u r display , u need to replace it ,

Apr 22, 2010 | T-Mobile Dash Smartphone

1 Answer

1988 F150 cranks / turns when trying to start but will not fire. it gets fuel, coil , ignition module changed, ingition unit on steeing wheel under dash has also been changed. acts like no combustion is...


no combustion or no compression? timing chain broke? you did not supply enough info about what you tested.or how. remove a spark plug wire if you dont like shcks take an old spark plug two alligator clips and a piece of wire attatch to the hex metal body of this old plug and connect the wire you just removed run the starter while watching for strong!!! spark.you can have a weak spark and no start=bad coil.i think but maybe wrong that this vehicle still uses aignition module located somewhere on the fender.find a parts locator maybe at the library. this module was aproblem for decades.have fun.

Feb 14, 2010 | 1988 Ford F 150

1 Answer

Lightbulb replacement for 2000 Subaru outback wagon


all you need to do is remove the clip holding the washer fluid neck filler, once this is out of the way you can access the big gray backing that should have two wires coming out of it. just twist in the direction indicated and remove the cap, now you have access to the back of the bulb, remove the wires attatched to it and remove the metal clip that holds the bulb in place. now just put the new one in. You will see a small tab on the round part of the bulb, below the glass, align it right in the slot and put the metal clip back on and put the wires back on and backing cap and washer filler cap. P.S do not touch the glass on the new bulb, the grease on your fingers will prematurely burn the bulb out.

Jun 26, 2009 | 2000 Subaru Outback

8 Answers

My samsung gravity's slider is broken when i slide it up something pops out right above the w???


mine did this and I fixed it really fast.
So there's a circle piece and a little metal wire sticking out of it. On the tip of the wire is a little black cirlce.
what you have to do is get the wire and circle back inside the phone.
you do this by pulling on the wire gently until the metal circle has almost disappeared. When the metal circle piece is almost entirely out of sight, slide the phone back to it's original postition (aka no keyboard). Unslide it and it should be almost as good as new.

May 06, 2009 | LG RUMOR Cellular Phone

1 Answer

Skybox parts # 4387535 installation issues


You don't need to keep the round metal piece or the black wire that you take. The replacement part (flat one) is installed in its place. Put it in first, attach the green wire to it, and then put the two prong piece and install the wires (blue, white and brown) as you took them off the original part.

Apr 17, 2009 | Maytag SkyBox MBV1976A Beverage Dispenser

1 Answer

Help on phone


Take the phone apart and make sure that the little motor with the weight is plugged in and that none of the wires are loose on either the board or the motor itself.

Hope this helps,
Simon.

Nov 19, 2008 | T-Mobile Dash Smartphone

1 Answer

Screen replaced, now phone won't vibrate - want to check wiring...


well when you open up the dash, theres a little metal thing that hangs by wires.. and thats the vibrater

Jan 05, 2008 | T-Mobile Dash Smartphone

Not finding what you are looking for?
T-Mobile Dash Smartphone Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top T-Mobile Computers & Internet Experts

ismael castillo

Level 2 Expert

318 Answers

yadayada
yadayada

Level 3 Expert

80407 Answers

Martin Murray

Level 3 Expert

1623 Answers

Are you a T-Mobile Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...