Question about Grundig GF70-600 TV

1 Answer

Grundig cuc2058 ny grundig tv keeps intermittently losing the picture (sound stays on ) and sometimes switches itself to stanby mode-tv is approx. 6 years old. seems worse when watching sky channel. is it fixable? and how much will it cost

Posted by on

1 Answer

Re: grundig cuc2058 - Grundig GF70-600 TV Standard (CRT) Televisions

Bin it

Posted on Dec 31, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My LCD32805HD tv keeps staying on stanby

Main board to your TV should be checked. Sometimes it might need replacement. Contact any experienced service technician.

Jul 02, 2012 | Standard (CRT) Televisions

1 Answer

Philips Magnavox 32MT3305 keeps shutting off with relay clicking. The green power light stays on but the picture and sound go out right after the orange status bar goes away. If the channel up or down...

the relay is the safety protective device..sometimes a defective component or something. maybe an overloaded power supply might caused this before any thing could gets worst..the relay will shut the unit..

Jul 18, 2011 | Philips 32MT3305 TV

1 Answer

When I turn on my Gundig TV the sound is there, but the picture does not come for about 15 minutes. It starts off blue then slowly changes colour and eventually comes on. The TV is only 16 months old....

It may be due to the fault of its picutre tube base socket. Some of them may show this type of fault eventhough it is a new one. Picture tube base socket is located at the picture tube bas card itself. It is directly soldered to the base card, throu which the connections are going into the picture tube via its pins. You just open the tv, and pull it out [not make any shakes while pulling it, as that may bed the picture tube pins, or iven break the picture tube neck. Just pull it straight out, and refit it at the same way as you pulled it out, for two or three times. Sometimes this will retify the fault, as this process will remove any loose contact between bascard socket and picture tube pins.
If this doesn't hlep, desolder it out from the picture tube base card, go for a similar type and pin confuguation. Replacing it will solve the problem. As you replacing the base socket, look into the base card for any loose soderings are there too. OK.

Nov 08, 2010 | Grundig 21" TV

1 Answer

My tv 32pw9617 switches of by itself.

sounds lick you may have a dry joint in the powers or line o/p stage.

as a rare fault it could be the crt with an intermittant internal s/c. but you would notice the colour was tinted either red, green, or blue in the dark areas of the pic.

Jul 13, 2009 | Standard (CRT) Televisions

1 Answer

RCA TV, model number 32V550T. No picture but sound is fine.


this sometimes is quite simple to fix as it cud be a dry joint on the circuit board where the tube motor sits.

or it cud be the tube is on its way out, which wud be cheaper to buy a new tv rather than have it fixed


Feb 24, 2009 | RCA 32V550T 32" TV

1 Answer

My Grundig tv turns itself off

Its Probably overheated.

happened to me before then i took to fixers and they changed some part and now its fine or if u have a warrenty call the manafactuarer

Dec 13, 2008 | Proton MM2701VT 27" TV

1 Answer

TV goes out

Intermittent problems are the toughest to track down, but usually have one of two root causes. Cold solder joints are an intermittent contact between where a component (transistor, etc) is mounted to the circuit board and the electrical contacts of the board itself. The other cause is components which break down under heat. Either way, if your not much on troubleshooting, have a TV shop service it, it can be easily repaired.

May 22, 2008 | Sylvania 6419TC 19" TV

1 Answer

Picture problem

Since it is 9 years model definetely loose contact and flux corrosion is there in wire connector and pcb also. Make one general service. Prolem solved.

Aug 23, 2007 | Toshiba CF35F50 TV

1 Answer

Grundig Xentia - sound but no picture

in your tv is malfunctioning high voltage, the audio is generated without the help of high voltage sistem how happens commonly in many other tv

Aug 07, 2007 | Grundig GF70-600 TV

1 Answer

Portable Grundig TV/vcr combo - screen goes blue and then set switches off.

Hi mcloud Your problem is your video circuit.the component could be faulty or it has lose solder.have a tech look on your set for repairs.good luck.

Apr 25, 2007 | Grundig GF70-600 TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Grundig Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

66623 Answers

matt martin
matt martin

Level 3 Expert

1187 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Grundig Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides