Lights flashing, but there is no one home

Hi,

Use the link below for you to have the diagram and bcomplete info for Hp J5783
http://www.partshere.com/models/hpprinters.asp?printer=Q8232C

http://www.partshere.com/hppictures/

I suggest you try the HP Support Forum at

Printer All in One Install Setup

fan turns? hear it and feel it.blow.? in must.
cd drive ejects? (button)
no text ever on the screen? this is first. all else more complex.
do the flash light trick?
http://www.pcdied.com/monitors.html#flashlighttest

no beeps
no flashing caps lock key (codes) if yes, what code.
step one is get BIOS and its screens working
even using and external VGA monitor will help.
and the magic Fn+F4 key to turn that on.
hp is down this morning...(support pages)

the G60 series uses a CCFL lamp, that blows out (easy)
or its inverter.
if external monitor works, and flashlight trick works
CCFL back lamps are dead.

buttons and lights The HP Deskjet printer buttons let you turn the printer on and off, cancel a print job, or resume printing. The lights give you visual cues about the state of the printer
cancel button

** Pressing this button cancels the current print job.

print cartridge status symbol and light **The light above the Print Cartridge Status symbol flashes when a print cartridge is low on ink or incorrectly installed.
resume button and light
**The light above the Resume button flashes when an action is required such as loading paper or clearing a paper jam. When the problem is fixed, press the Resume button to continue printing.
power button and light **
The Power button turns the printer on and off. It takes approximately five seconds for the printer to turn on after you press the Power button. The green light above the Power button flashes when printing is in progress. Caution! Always use the Power button on the front of the printer to turn the printer on and off. Using a power strip, surge protector, or a wallmounted switch to turn the printer on and off may cause premature printer failure

Welcome to FixYa!

Try to reset the printer by doing the following;

1. Turn ON the printer.
2. Disconnect the USB printer cable at the back of your printer while the printer is ON.
The USB printer cable looks like the image below.



3. Open the Cartridge Door and remove the cartridge. Refer to the image below.

.
4. Wait for the "Insert Cartridges" message to display on the message screen of the printer.
5. Disconnect the power cord from the back of the printer.
6. Wait for 1 minute.
7. Reconnect the power cord.
8. If the printer does not turn on, use the power button to turn it on.
9. Reinsert the cartridges.
10. If the printer prompts you to print a calibration page or requests for a cartridge alignment, please do so.
11. Reconnect back the USB printer cable and try to print.

I hope that this would be helpful to you, thank you for usng FixYa!
Jas247

Try perform these steps as --->
Please perform these steps as please disconnect the power cable and press the power key for 30 seconds and at the same time connect the power cable then turn on the printer and let me know the status


And also perform this steps as 1. Disconnect and then reconnect the power cord.

2. When the lights begin to flash, press and hold On and Copies button.

When only the On light is flashing, release the buttons.

When the On light is steady, 1. Disconnect and then reconnect the power cord.

2. When the lights begin to flash, press and hold On and Copies button.

When only the On light is flashing, release the buttons.

When the On light is steady, the reset is complete. the reset is complete.


If the printer works then good
Otherwise Hardware issue

no problems
:just go ahead and take out the power cable when the printer is still on
:nw press and hold the power button fr 30 seconds
;while holding the power button,plug back the power cable
:nw u will be able to work well

Perform a partial reset of the HP All-in-One

1. Turn on the HP All-in-One.
2. Disconnect the power cord from the back of the unit.
3. Press and hold the # and 3 buttons simultaneously.
4. While still holding down the # and 3 buttons, connect the power cord to the back of the unit.
5. Continue holding the buttons until the Power button blinks.
6. Follow the instructions that display on the unit to select the language settings.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Hi

The HP Deskjet 6127 has four buttons and three lights on the front panel

Flashing lights on the printer indicate the status of the printer

When all the lights are flashing, the printer may need to be restarted

try this 1st press the power button to turn off the printer, and then press the power button to it back on very quickly.

2nd press the power button to turn off the printer and hold it down.

Good luck

all lights are flashing
the printer may need to be restarted
1. Press the Power button to turn off the printer, then press the Power button to
restart the printer.
Proceed to step 2 if the lights continue to flash.
2. Press the Power button to turn off the printer.
3. Disconnect the printer's power cord from the electrical outlet.
4. Reconnect the printer's power cord to the electrical outlet.
5. Press the Power button to turn on the printer.

If these steps do not work. It will need service, as a bad board may be the problem.

Here is the manual.

http://h10025.www1.hp.com/ewfrf/wc/manualCategory?product=304431&cc=us&lc=en&dlc=en&product=304431&dlc=en&lang=en