Question about VISION GUARD VISION GUARD 8000 SECURITY & REMOTE ENGINE STARTER SYSTEM WITH

1 Answer

Installing problems i don't know what wire goes where, its so confusing from all the color of the wires and thats really mainly it i just need help with that if u can send me something SHOWING me how to do it, that'll be great. thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 67 Answers

I don't have anything showing it, but I have a paging alarm I installed myself. The best references for me were on the Bulldog Security Site, http://www.bulldogsecurity.com/. The manual should explain what wires are what for the alarm. At this point, just get a piece of paper, and try drawing out what wire will go to what. You will not need all the wires, most likely, so don't freak if they are not all used.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I wire a two wire plug that plugs into an ignition control modular


You really should get an electrician if you dont know this stuff.. There is too much confusion and danger. I know the answer - but I wont tell you .. sorry

Aug 13, 2014 | Cars & Trucks

2 Answers

76 k5 blazer starter wiring confusion


Usually one is small enough to fit on the small terminal and the rest fit on with the battery cable.
The small purple wire from the key switch goes on the terminal marked S.
You could do a continuity test and check it with the battery disconnected by checking it back to the neutral safety switch.

Feb 11, 2013 | Cars & Trucks

1 Answer

I have a 3wire prong dryer and the outlet os for a 4 prong dryer, l have the 4 prong cord but don't know how to connect it can you help?


Hello,

It seems to get confusing where the wires go in the back where the cord connects to on your brand new,or previously dryer that you have brought to a home thats new to you

4 wires goes as such with oldtech2332.jpgthe red wire going on the right side,the black wire going on the left,the white wire goes on the center terminal. Now what exactly do you do with the green wires is what your asking yourself. It goes onto the cabinet after removing that little link that went from the center terminal that was beweeen the cabinet and and the white wire terminal.Yes remove that link and install the green wire where that link was just attached to a minute ago


GENE

Oct 16, 2011 | Dryers

1 Answer

Need to know which color wire on a new plug goes to which screw on the back


Hello,
This is how to connect both 3&4 wire cords;
It seems to get confusing where the wires go in the back where the cord connects to on your brand new,or previously dryer that you have brought to a home thats new to you

4 wires goes as such with oldtech2332.jpgthe red wire going on the right side,the black wire going on the left,the white wire goes on the center terminal. Now what exactly do you do with the green wires is what your asking yourself. It goes onto the cabinet after removing that little link that went from the center terminal that was beweeen the cabinet and and the white wire terminal.Yes remove that link and install the green wire where that link was just attached to a minute ago.

3 WIRE CORD

oldtech2332_0.jpg
The 3 wire cord goes just like this see the 2 wires on the outsides of the cord going to the black/red wires .The wire in the middle of the cord goes on the middle terminal on the cord block

Aug 27, 2011 | Whirlpool LER4634J Electric Dryer

1 Answer

I have a malibu ML 88T low voltage transformer. It was working fine and I saw the manual on/off and turned it, (i should have left it alone). The lights did not come on, so I turned the manual on/off...


You can do it yourself.
Anybody that knows 'hardwired' and observed timer is making humming sound can wire up a timer.
If M88T timer dial is not rotating, but power pack is making humming sound, then that says timer is receiving power but clock motor has gone bad.
There are no replacement clock motors for power packs.
http://waterheatertimer.org/Malibu-power-pack-stopped-working.html

To wire a new timer:
Click circuit breakers until the humming sound turns off.
Turn breaker back on to confirm that humming sound is associated with that breaker.
Buy a tester at local hardware and ask them how to use it.
Tester will give you assurance that power is off when connecting new timer.

Outdoors: put down dry boards to stand on, never stand on bare soil or wet/damp surface, don't touch anything metal and don't hold metal screwdriver in mouth while working on electric circuit. Wear gloves if you want. And don't sweat.
With 120volt circuit, as long as you are not grounded, which means that you are not touching soil, or anything that grounds back to soil, then you will not get electrocuted. You can get shocked only if power is still turned on at circuit breaker, and it will be surprising, but it won't kill you as long as you're not grounded. All electricity goes back into the earth to complete circuit.

Open the box where timer is hardwired.
Use tester on black wire. To confirm power is off.
Typical 120volt circuit: Black wire is Hot and carries voltage. White wire is neutral and completes the circuit back to ground. Bare copper wire is ground and serves as redundant safety.

Old 88T timer will be wired black-to-black, white-to-white, and green-to-bare copper.
Take photo of wiring to avoid confusion. Post photo on flickr and add a comment with link to photo for another pair of eyes on situation.
Cut off end of new timer wire, strip insulation with knife and attach wires same way previous timer was connected.
http://waterheatertimer.org/How-to-twist-electric-wire.html

To install ordinary 120Volt outlet so timer can plug in: Buy outlet from hardware: Black hot wire connects to brass-colored screw, white neutral wire connects to silver-colored screw, bare ground wire connects to green-colored screw.

Open following link to see basic circuits:
http://waterheatertimer.org/B220C.html
http://waterheatertimer.org/See-inside-main-breaker-box.html

Aug 08, 2011 | Intermatic 24hr Outdoor Timer

1 Answer

HI ,I HAVE A FORD PROBE. IT HAS THE 2007R RDS STEREO IN IT . SILLY QUESTION BUT WHAT IS THE OTHER CABLE FOR THAT GOES INTO THE BACK OF THE STEREO THAT IS GREY IN COLOUR AND QUITE THICK, AND I DONT MEAN THE...


I think that it is a ground or the antenna wire but if you are putting a new stereo in all you really have to worry about with the power is the constant hot which should be a yellow wire, the control wire which should be a red wire and the ground which should be a black wire with a grey stripe on it then all you have to worry about is the speakers, I usually run new wires to speakers but you don't have to so i really cant help you there, how they have the speaker wires set up is confusing, that's why i just run new wires usually 14 gauge for best sound quality. 2q== this is what the antenna wire should look like.

Jun 30, 2011 | Car Audio & Video

1 Answer

Hello, Im trying to rewiremy transmission on a 92 GMC 3500 vandura box van. My don chewed the wiring that plugs into the transmission The plug has 11 wires coming out of it but some of them that he didnt...


Hello tnvolsfan32,

Use the FREE drawing available on the
BBB Industries site to trace out your wiring...
BBB Industries Premium Alternators Starters Power Steering Products

First put the wires together that
DO PERFECTLY MATCH... Then go
back to the drawing and find out what
DEVICE, CONNECTOR or PLUG got
disconnected or swallowed.

Generally wires DON'T CHANGE COLORS
in a wiring harness run... So you definitely
need to look for a LOGICAL EXPLANATION.

Registration is required... these are real
wiring documents...

Each time you return from a WIRING page
make sure you have not
defaulted back into TSBs...
(technical service bulletins)... While usually
quite useful... they don't begin to address any
WIRE-EATING-DOG problems...

If you get confused comment me back...
I can recommend some great tools to help
SPLICE everything back together

Tone Tracer being PRIMARY
Extech TG20 Wire Tracer and Tone Generator Amazon com

Helpful hint: wire must be ISOLATED to trace correctly
(pulled fuse or chewed through works).

Hope this helps

Carnac the Magnificent

Sep 23, 2017 | GMC Cars & Trucks

1 Answer

I need the radio wire color code or wiring diagram


two purple wires, speaker
two white wires, speaker
two gray wires, speaker
two green wires, speaker
black wire, ground
yellow wire, battery...for memory( goes to a constant 12V power source)
red wire, ignition, to pwr on when key is on
blue wire(remote wire if you have a system)

Mar 18, 2010 | Chevrolet C1500 Cars & Trucks

1 Answer

My revirse lights do not work


Really dont need to know color of wire for this system is simple. On the switch (left rear corner on transmission) there are three wires. one wire is power, one allows it to start in park or neutral and the other is for the reverse lights. If I remember correctly the two outer terminals operate the reverse lights. Find the power lead and jump to each of the other two to determine which is for the reverse lights. Likely you will find that the switch is bad and there is no wiring problem. Make sure that reverse lights have good grounds as well.

Aug 16, 2009 | 1987 Dodge Ram Wagon B250

Not finding what you are looking for?
VISION GUARD VISION GUARD 8000 SECURITY & REMOTE ENGINE STARTER SYSTEM WITH Logo

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buck Vehicle Parts & Accessories Experts

xxxxxx xxx

Level 3 Expert

4874 Answers

Rocguy

Level 2 Expert

255 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Buck Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...