Question about Home

1 Answer

Need an owners manual or a relay wiring diagram for a Mr. Spa hot tub 303 or 404. serial number 6229 Its an older hot tub with 2 relays that control 4 electrical plugs for the blower,pump blower and pump.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 248 Answers

Should be able to pick up one online

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a LX80 Commercial pool and Spa Control System made by Pentair. I notice this morning that the jet spa motor was running all the time. Which is not right because the control panel is set for 15 min....


If you are positive that the two hot lines onto the motor relay are in the correct postition, then it is the control wires not giving power to the relay to close the circuit. Make sure the signal wires are connected to the contrl board. then, check to see if the timer is still working. its always possible that the control board has failed under the surge conditions. If signal wiring is in place and relay still wont close the circuit, disconnect the relay signal wires, set the timer to come on, and after it tries to activate that relay, measure for 24 volts at the relay signal wire terminals. If no voltage is found, bad timer, or bad board.

http://www.pentairpool.com/pdfs/LX80IG.pdf
above link has wiring diagram included incase needed

Jun 08, 2011 | Pentair LX802L Commercial Pool/Spa Control...

1 Answer

I have a Ramco spa pack and the heater works at first but once it reaches temp and turns off. When the heater tries to kick back on the contactor will chatter and not close all the way unless i push it...


The chattering is exactly what happens when a relay fails. If this is an older model tub, it is likely that you can just replace the ice cube relay. If it is a newer tub, the relay is most likely imprinted into the main cpu board, in which case you have to have somebody put a new relay on the board for you, or replace the control board. If this is an older tub and you need help sourcing parts, you can contact me @
adamh@newconceptchem.com

Nov 24, 2010 | Pool & Spa

1 Answer

Hot tub not heating need owners manual to reset


You need to provide the exact make and model of your spa

Dec 12, 2009 | RTO 2 Person Spa Hot Tub 8 Hydrotherapy...

2 Answers

Jet pump will not shutt off after I replaced heater relay. Tub is a hot springs landmark with an IQ2000 panel the year is also a 2000


it sounds like the pump relay may be stuck closed. Also check the temp readout, if it thinks the water is too hot it will try to cool the water by running the jets and sometimes the blower as well.

Dec 08, 2009 | RTO 2 Person Spa Hot Tub 8 Hydrotherapy...

1 Answer

Just filledd up an old dakota hot tub model126-dkn-4248-2 and ita been running for about 4 hous and wont heat up i would also like an owners manual for one but dont know were to look


it may take longer to heat to desire temp. if nothing chang have you adjust the temp higher . if everything check ok check high limit switch next to the control box ussualy red bottom push soft in

Sep 13, 2009 | RTO 2 Person Spa Hot Tub 8 Hydrotherapy...

2 Answers

Hot tub


go to the manufactures website or just google (the name + service manual/owners manual)

Apr 10, 2009 | Waterway 4 Hp 230 Volt 1 Speed Side...

1 Answer

Finding the spa manufacturer


That serial code is for the controls, not the hot tub.

Usually manufacturers will attach a plaque with the hot tub details on.... this would usually be at the front of the hot tub, either on the inside of a cabinet panel, or on the exterior.

Regards,
Ian.
http://hottub.synthasite.com

Apr 05, 2009 | Estate TEDX640JQ Electric Dryer

Not finding what you are looking for?
Home Logo

Related Topics:

562 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Experts

Donni Steen

Level 3 Expert

659 Answers

Tom Chichester

Level 3 Expert

34100 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...