Question about Zebra Z4Mplus Label Printer

1 Answer

Printing die cut labels on Zebra Z4Mplus?

Hi, I am trying to print some round labels on my Zebra Z4Mplus, but I can't get it to detect the labels properly. I have done some other die cut labels in the past but they had a sensing mark printed on the back. I was under the impression that I wouldn't need that mark to print die cut labels.

Can anyone add any advice or feedback?

Thanks!

ApexZebra

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 38 Answers

Set the printer to transmissivefrom reflective gap sensing.

This will cause the printer to loog for the inter-label gap to tell it where the top of the label is at.

Steve Weinrich
LazerTek, LLC

Posted on Mar 30, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My zebra z4mplus just start printing at the center of the label instead of at the left side of the label. Instead of a normal full printing on a label, now the left half of the label is blank, and the...


Welcome to FixYa.
The Zerba Driver might have been corrupted.
Uninstall the Zebra Driver/Software from the Control Panel.Re-install the Zebra driver using the Disc that came along with the printer.
Thank you for using FixYa.Have a great day.

Nov 29, 2011 | Zebra Z4Mplus Label Printer

1 Answer

How do I configure a Zebrazm4 Plus printer for a


Usually the easiest way to do this is to make sure the printer driver you're using is set for continous labels. This setting will vary depending on the driver / software being used to print labels. You can also go into the SETUP mode on the printer and make sure MEDIA TYPE is set to continous. Be aware that most printer drivers will override the setting in the printer. You may set to continous in the printer but if the software is set for die cut labels, then the printer will act for printing die cut labels when a format is sent to the printer.

Mar 25, 2010 | Zebra Z4Mplus Label Printer

1 Answer

Label alignment


see if you can download from here: http://www.zebra.com/id/zebra/na/en/index/resource_library/manuals.results.html

Z4MPlus Users guide is the fourth one down.

Mar 12, 2010 | Zebra Z4Mplus Label Printer

1 Answer

My Zebra Z4Mplus printer is skipping labels when I print


check the label margins, and label dimensions, and spacing , normaly is these problem, or is a printer driver problem, try reinstall driver

Jan 13, 2010 | Zebra Z4Mplus Label Printer

1 Answer

Zebra Z4MPlus Ribbon Wrinkles


I changed the print head, and the issue was solved.

Aug 01, 2008 | Zebra Z4Mplus Label Printer

1 Answer

Label size


Set the label size in the label program and then calibrate the printer.

Jul 11, 2008 | Zebra Z4Mplus Label Printer

1 Answer

Stops printing after sending job


try to reset to factory defult,
run calibration and sensor profile.
if dont help,
it is possible that the power suply or logic board is faulty.

Jun 30, 2008 | Zebra Z4Mplus Label Printer

1 Answer

Label Printing


Forward length matters in Label size detection. Width is just secondary. Length should be same for both. Else no, you have to had separate roll for each label size.

If the labels are same in length then there might be achance using Label Software that supports your printer.

Jan 24, 2008 | Zebra Z4Mplus Label Printer

1 Answer

When printing more then 10 labels from Acrobat some of them are missing


Hello!
Dear
I need ur assistance about this types of Model TLP-2844,LP-2844,S4M,S-600,105SL,110xiii,140xiiiPlus,Z4M,Z4MPlus,How can I Install a Printer With Label and Ribbon?Can U help me regarding this problem?I am waiting for ur assistance.If possible please send me a video file about how to Install a Zebra Printer with label and Ribbon.

Dec 13, 2007 | Zebra Z4Mplus Label Printer

Not finding what you are looking for?
Zebra Z4Mplus Label Printer Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

Dave Busselle

Level 1 Expert

54 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...