Question about KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

1 Answer

Stopped Dead I have a KitchenAid model KUDM01TJBS1. We started the machine and it partially filled and then went dead. Has power to machine but no response. Any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 65 Answers
Re: Stopped Dead

Thermal fuse attached to control board. it is white in color. You should have power at both terminals on this part.

Posted on Feb 16, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Came back from week long vacation (was working fine when we left) Went to start it tonight and doesn't work? seems like it is dead?

check for power at the outlet that it is plugged into under the sink,, one of the GFI outlets could have tripped or is broken.


Feb 21, 2011 | Jenn-Air Dishwashers

1 Answer

Washer went dead. replaced thermal fuse and it worked for about a week and went dead again. Before going dead it seemed to take it a long time to do a load of dishes. The last load ran 1 1/2 hours and...

sounds like you have a bad control board on unit.and the reason the thermal fuse went out is one of the relays are getting stuck on unit. before long the fuse will go bad again when the resistance level gets to high again. i would replace the control board and you should be fine...good luck to you...

Jan 06, 2011 | KitchenAid 24 in. KUDP01DL Built-in...

1 Answer

I have a KitchenAid KUDSFLxxx dishswaher - a couple of weeks ago it stopped working (looked dead) - I took the door apart and tested the switches in the door latch - tested good - started playing around -...


If you have replaced the control panel then it is the electronic control board that is bad and should be replaced. If you have replaced the electronic control board then check the door latch, it can be due to the latch & control not operating. Hope this helps...please post back with its model no. for further assistance.


Dec 08, 2010 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

Water doesn't drain. none of the buttons work, now.

hello sir
please check whether the power supply is reaching the machine or not.

Jul 06, 2009 | KitchenAid KUDK03ITBK Built-in Dishwasher

1 Answer

Brand New Bosch Stopped Working On First Use

No question that it is a warranty problem, you shouldn't consider doing anything on the machine yourself at this point.
After the warranty is dead and it fails, c'mon back and you will likely find someone to help. It is good though, that we are forewarned about Bosch-

Jun 21, 2009 | KitchenAid KUDK03ITBK Built-in Dishwasher

1 Answer

Top drawer stuck, gaskets rubbing, no power to controls

I see the question is posted in the DD603 section, so I am not sure if I am giving the proper advice. Are you sure this is a 602/601 series? A DD603 model has lid actuator motors, not the inflatable style seal. It sounds like the lid motors are in the DOWN position. Since the machine is "dead" what may have happened is the heater plate opened up (the heater plate is a dropping resistor inline with the machine's controller) when the machine was in use and that stopped everything dead.
Double-check your model number so we know what style of lid your machine has, The difference is huge between models.

Dec 31, 2008 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Dishwasher stopped in early cycle. No power

Hi, did the d/washer fill? or is it dead from the wall into the machine? I.E. is there a mains light on to show power?

Dec 28, 2008 | GE Dishwashers

1 Answer

Kitchenaid KUDM01TJBS1

Open the door and at the bottom right is a float switch. Make sure it's working and nothing is obstructing it.

Jun 01, 2008 | KitchenAid 24 in. KUDM01TJ - Multiple...

1 Answer

Kitchenaid KUDR01PJWH1 stopped midcycle. Water still in bottom. Controls not lighting up. Dead?

Checked fuse in control panel for continuity. None. Ordered fuse. Will start with fuse and then electronic control panel next.

May 26, 2008 | Dishwashers

Not finding what you are looking for?
KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher Logo

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides