Question about IBM FRU POWER/RESET CARD 73P6310 Power Supply

1 Answer

I need ur help plz

I have a kenwood deck that i bought from a friend and i lost the code and he doesnt remember it do u knnow how to reset it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers
Re: i need ur help plz - IBM FRU POWER/RESET CARD 73P6310 Power Supply System Power Supplies

You must call the factory

Posted on Mar 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

4 Answers

I am wanting to reset the system password on my dell computer

click start control panel Open User Accounts in Control Panel. On the Users tab, click the name of the user whose password you want to change, and then click Reset Password. In New password and Confirm new password, type the new password, and then click OK. Notes You can change passwords only for local computer accounts, such as guest, administrator, or accounts you create for your computer. You cannot change your network logon password in User Accounts. To change your own password, press CTRL ALT DELETE and then click Change Password also if you want set a BIOS password during the boot up process you will see on the screen for a short amount of time to press a certain key to enter set up Press and hold that key during the boot up process to enter BIOS scroll down to set user password or supervisor password you can change or remove your password from there also click start control panel user accounts on the users tab click the name of the computer administrator you can change the password there hope this helps you should make a note of any passwords and keep them separate to your computer incase of memory lapses

Aug 07, 2011 | Dell System Power Supplies

2 Answers

Res sir, i use zebronic ups model:u700 how to i put the ups into charging mode

if ur nt a pro..plz do consult ur system admin/vendor n try for a battery replace..if prob persists do check the main transformer, relays n associated circuit at d charging/push pull unit/sec....

Apr 28, 2011 | System Power Supplies

1 Answer

Hp pavilion a450n turns on but wont open past countdown

probably itz either minor case of software corruption/improper ground/cpu fan..
or major case of faulty or defective main board/ram/daughter or addon card(s)..

..plz do check the following as in order:..
the Hardware part:..
1)see if the ram(s) is loose/ clean/remove carbon & or oxide formed on the teeth with an eraser n resit it..or replace with a standby n see..

2) 4) a) see if ur hdd is noisy or emitting any 'ticking' noise (like 'tuk tuk' or 'kirr kirr')..
b) or if the system is not supporting either the newly installed device or itz software/driver /firmware
if so, u need either a fresh os installation or ur hdd is likely to b replaced..

3)remove/clean dust neatly..dust is non-uniform in nature n may cause jam/short circuitry/excess resistance n many more..resulting an increase in heat..

4) open the CPU Heat-Sink with fan out of the socket..put some "Heat Sink Compound" (available in local electronics chip level spare market) between the cpu/processor and the CPU Heat Sink *** fan..resit/fit it tightly in position..

5) on main/mother board..see with a debug card for mb error..may b short..look for defective capacitors(esp above1000mfd)/mosfets..go through the mb's south bridge n the circuit lie around atx connector..the crystal clock generator (if cpu isn't heating up)..

6) [in case of desktop] the smps itself may b defective/faulty..check the outputs of smps viz. 0v (black~ground); +12v (yellow); +5v (red, green~ps-on, violet~pg & grey~sb); -12v (blue); -5v(white); +3.3v(orange)..the 'oscillator and error amplifier ic', or pwm switching regulator circuit..look for defective protector-transformer/resistance(esp 4.7k)/mosfet..
check the battery [both main power & cmos], in case of laptops..

the Software part:..
1) hv a licensed and UPDATED antivirus installed (i prefer avg/kaspersky, remember, without updation a full version antivirus is useless)..

2) download, install n run microsoft kb890830..

3) download n run Startup Control Panel..'remove all the unnecessary startup items from here..(if u can't find what to remove, post me/us in ur comment with all the items listed in each n every tabs herein)..

4) remove all unnecessary software from add/remove programs..

5) download, install n run 'Advanced System Care Pro'..

6)disable the following:..
a) 'Automatically Restart' right click on my computer->properties->advanced->startup n recovery->(uncheck on the) Automatically Restart;
b)'Error Reporting' right click on my computer->properties->advanced->error reporting->disable error reporting->(uncheck on the) 'but notify me when critical error occur'..

7) Increase the size of Virtual Memory, Initial: 1440; Maximum: 2880

if u r bot a professional, always better to seek advise from ur system admin/vendor....

Nov 15, 2009 | HP System Power Supplies

1 Answer

Hi I have Bought a dedicated micro sprite 2 dvr with no hard drives. I have download the software from dm site and installed them. the dvr boots from it. but i need to restore it to factory settings. I...

tony i have the same issue and it need to go to a repair shop or seller to reset , and it can be expensive if its to go back to dedicated micros. Find your nearest repair shop cheaper in the long term

Aug 24, 2009 | Dedicated Micros Power Supply

1 Answer

Need user manual for Kenwood power supply PD56-6D

I could not find it free(the manual) but if you want to buy one ($23) it is available here. Hope this helps.

Mar 25, 2009 | Kenwood (PD56-10AD) Power Supply

1 Answer

3 beeps every few minutes

That maybe a memory beep code. Turn it off and remove and re-insert the memory modules on the mainboard.

If this doesnt work, get back to me.

Feb 13, 2009 | Apex Computer Technology Apex Power Supply...

1 Answer

Kenwood Power Supply Dip Switch Setting

why don't you get a controller for that supply? I got one...

Jul 08, 2008 | Kenwood (PDS36-20) Power Supply

4 Answers

Power supply problem

i have a compaq computer power supply its not given the constant volts plz help

Jun 04, 2008 | Compaq (176763001) 120-Watt Power Supply

Not finding what you are looking for?
System Power Supplies Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top IBM System Power Supplies Experts

Shahzad  Waseem...
Shahzad Waseem...

Level 3 Expert

746 Answers


Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you an IBM System Power Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides