Question about Enterasys Cabletron SmartSwitch 2200 w/ 24 Ethernet Ports&(2) AC Power Supplies 2E42-27R (2E4227RREF)

1 Answer

Ethernet problem Trying to switch to high speed from dial up. Installation process says no ethernet card. Ethernet card is not showing up in device manager. Is it safe to assume the card in no good or could it be a driver? Using a Dell Pentium III desktop, windowsXP SK

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers
Re: Ethernet problem

If card is in PCI slot sometimes switching slots will make it start working.

Posted on Jan 02, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Does a Ethernet Switch(Unmanaged) have a default IP address?

There is a user guide on the tp-link web site. It looks as if this is just a layer-2 switch (ethernet) and there is no user configuration to enter. The IP addresses would come from another device on your LAN. A router or a server that supports layer-3 (IP) would issue addresses by running a DHCP server process on it.

Nov 02, 2013 | TP-LINK TL-SF1008D 8-Port Ethernet Switch

1 Answer

How do i install?

This device is a plug and play device and doesnt need any configuration before installation.

You need CAT6 ethernet ( copper LAN cables) to connect the switch to the other device from where you want to extend/expand your ethernet.

Best Regards

Dec 31, 2010 | Dynex DXESW5 5Port Ethernet Switch

2 Answers

Getting low or no connectivity error when trying to connect laptop and other devices to 5-port DLINK switch. Lan line going to switch is confirmed working as i'm able to plug the laptop and other devices...

please change the cable which is connecting your laptop to D-Link DES 1005 Ethernet Switch.

This error appears when you have either a bad cable or bad switch or NIC card on Laptop.
As you have Laptop and other devices and getting the same error , so i suspect issue with the cable.

Please use a new Straight LAN cable.

Oct 31, 2010 | D-Link DES 1005 Ethernet Switch

1 Answer

1 connected ethernet cable from modem to dynex hub in "uplink port", ran another ethernet cable from laptop to 2nd port on dynex hub and ethernet cable from ps3 to 3rd port and nothing happens. Please help...

If your trying to use this to share an internet connection.. sorry to say but it's not going to happen. The hub that you purchased will not handle the DHCP settings that need to be processed to share an internet connection.

Best advice... go back to Best Buy and smack the agent that sold you this and get a router instead. :D That's what you're needing to share your connection.

Oct 23, 2010 | Dynex 4-Port 10 Mbps Ethernet Hub

1 Answer

My 3com 4200 28 ports is restarting by itself many

Base from the description of your problem its only showing that some of the port on of your Ethernet switch is already getting bad and this usually happen on switch like this and eventually all port will go bad and will lead to the replacement of the device. With this type of problem you can first try to adjust the speed of your network card to 10 half duplex and check if that will correct the connectivity problem and if it does its just a sign that sooner or later the device is already getting bad and since its only a switch there's no firmware that we can load to it or even a reset button to bring the device back to its default settings.

Jan 27, 2010 | 3Com 4200 24-Port Ethernet Switch

1 Answer

Network cable speed problems

1GB ethernet is a theoretical speed the pc other components [motherboard] may not have full support for network card, also the card may be wrongly conigured

Oct 24, 2009 | Cisco Catalyst 3750-E 48-Port Gigabit...

1 Answer

Dynamode ht809stp

just plug the power connection
and connect the network cables. and restart the computer.

Summary for Dynamode (HT809STP)
Dynamode products have earned a worldwide reputation for quality. The Dynamode hubs products utilize state-of-the-art design and ASIC-base hardware for high reliability.Dynamode offers the 8-port Ethernet Hub which, in compliance with IEEE 802.3 10 BASE-T standard, is a multi port repeater used in the twisted pair Ethernet Network. Featuring 8 RJ-45 twisted pair ports for twisted pair wiring, one AUI port for thick cabling and one BNC port for thin cabling, it allows to connect up to 8 devices (such as twisted pair Ethernet card), an Ethernet Transceiver and a Tee connector.

Sep 16, 2008 | Dynamode (HT809STP) Networking Hub

3 Answers

Switch port

switch setting
int f0/1
speed 100
dup full

and lan card shuld be shud be more then 100mbps or 1gb
then it will conect to full duplex means

u have to to any device shud have same duplex

Aug 11, 2007 | Cisco Catalyst 2950 24x10/100 Mbps...

Not finding what you are looking for?
Networking Hubs & Switches Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Enterasys Networking Hubs & Switches Experts


Level 3 Expert

4327 Answers


Level 3 Expert

18258 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you an Enterasys Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides