Question about Roper RAS6233KQ Top Load Washer

1 Answer

Can't get the top off to check the lid switch

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,356 Answers

Typically the top section needs to be pulled forward, then it can be coaxed off of the front clips.

If that does not work, release from the rear of the machine.

Posted on Sep 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The machine does not perform last spin cycle


check lid..either the lid switch is bad or the lid switch actuator which is made into top...when in final spin push down on the right hand top part of lid,,,if it starts replace part needed,,,good luck

Sep 12, 2011 | Avanti Top Load Washer W797

2 Answers

Model # lat8826aae my washer doesnt work when i close the top load cover


open timer console and replace fuse can get from any hardware store

Jan 27, 2011 | Maytag Washing Machines

2 Answers

Have to slam lid so lid switch will make,where is the lid switch located


The lid switch is here:themobilian_773.jpgTo check it flip up the controls and unplug it's quick connectthemobilian_774.jpgThe connect has 3 wires, a green ground and two other wires, those two other wires go to the switch. Here is a video that show how to replace that lid switch:
I have a manual and some more videos HERE

Thanks for using FixYa
themobilian_775.jpg

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jan 07, 2011 | Whirlpool LSR5132PQ Top Load Washer

1 Answer

LS error


The machine control detected that the lid switch is not functioning properly. Raise the top part of the washer to gain access to the lid switch.

Disconnect the machine from the power source. Gently pry the emblem from the front of the machine and remove the T20 torx screw hidden behind it. Slide the top of the washer forward and raise its front. Prop it up high enough to allow easy access to the lid switch.

The lid switch is activated by an actuator (part number 19119) mounted on a hinge. It will not work properly if the actuator is damaged.

Check the operation of the lid switch using a multimeter. Disconnect the lid switch wiring harness and connect the test leads of the multimeter (set to X1 or ohm) to the terminals of the lid switch and activate it. The multimeter should read zero ohms while the lid switch is activated and open when deactivated.

Replace the lid switch if it is broken or if it fails the test above. Remove the lid switch mounting screw and install the new lid switch. Reconnect the wiring harness and slide the top of the washer back into position. Reinstall the T20 torx screw and the emblem.

Feb 11, 2010 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Whirpool Ultimate Care II - Top loading washer The water will not drain prior to the spin cylce - Please help


The lid switch is the most probablle cause for this problem.Check the lid switch lift the lid and close it if you cant hear a click replace the lid switch.

Dec 28, 2009 | Whirlpool LTE6234D Top Load Stacked...

2 Answers

Washing machine stops mid-cycle, water doesn't drain


Sounds like you have a bad lid switch, or the plastic plunger on the lid that engages the lid switch is broke. if the plunger is broke, it is cheap, and only 2 screws to remove and put new one on. if that is not broke, check the lid switch. This model is a lid switch, and lid lock in one. You can test it before replacing it if you have a meter. you need to hinge the lid up to check and replace the lid switch. use a putty knife, on each side between the top and top of the front panel. slide the putty knife in one side, it will hit a bracket if your in the right spot. press in, and lift on that side of the top. do the same on other side, just don't let go of the first side or it will latch again. then swing the top back, the back side is on hinges. the lid switch is on the right side attached to the top. unplug washer, remove the 2 wires on the switch and check continuity. there should be continuity, or "open" when the lid is closed, and no continuity, or "closed" when you open the lid. if it is "closed" even when lid is closed, replace the lid switch. let me know if you have any further questions, shane.

Sep 12, 2009 | Washing Machines

1 Answer

My kenmore washing machine will not enter into the last cycle and will not rinse out. Silly as it may seem banging on top of the machine with the lid closed sometimes gets the machine to start again and...


Hi, check lid switch, open lid, check carefully locate lid switch, or lift top of machine, get access to lid switch, could be broken or faulty, also check all wiring harnesses, there could be loose connection, check timer connections, all other connection, but first check your lid switch. when you lift lid, look for small slot, on machine around area lid covers, use something to press and release lid switch, preferable something non conductive, i use a small screwdriver. it could be just broken / faulty lid switch, or loose connection, you can check yourself, or let someone check for you, that's no big deal, always switch off power, before doing any repairs. good luck.

Aug 13, 2009 | Washing Machines

1 Answer

My kenmore 90 series is agitating but not draining the water or spining


Check the lid switch. The lid switch will be located on the machine top where the lid closes. It may be a plunger on the lid that activates the switch or a white plastic flat piece where the lids sets. Either scenario can be checked by jumping out the lid switch. Disconnect the power. Lift the lid. Use alligator clips to connect the two terminals. Plug in the machine. Select spin. If, the machine operates you have a bad lid switch.

Jun 15, 2009 | Kenmore 23822 Top Load Washer

1 Answer

No Spin No Drain


Lid switch is most likely the problem, if lid switch is visible under lid on right side then this is older design and common problem switch.
if you have console frame covers on front sides, snap off from top, a screw is at bottom front corners of console, remove and pull console forward and fold back. If lid swich is hidden then you will see it at left on top of cabinet with console folded back. a 5/16 screw holds a green ground wire to cab. remove and switch will unclip with lid up. If lid switch was visible under lid then you need to remove 2 brass clips holding cabinet on top of base to back, pry with screwdriver to unclip. undo harness connection on cabinet top, this is your lid switch connection. sw body is held by 2 phillips screws, harness tube held by clips on underside of cabinet top. ground wire with 5/16 screw present at sw body. New versions of this switch have metel shield attached.

Apr 25, 2009 | Kenmore 22642 Top Load Washer

2 Answers

My Neptune top-loader washer,


Evidently the "OP" code indicates the lid is "open". Solution in my case: I had to replace a wire on the lid switch that a
had rusted and no longer connected to the switch resister.

There is a magnet in the left, front corner of the plastic lid insert. When the lid is closed, this magnet sets on top of the tan colored plastic pad on the left front top of the base washer unit. When the lid is closed, the magnet activates two, small metal rods on each end of a resister within the white. You have to pop up the top of the washer base to gain access to the switch, Good luck,

Aug 29, 2008 | Maytag Neptune FAV6800AW Top Load Washer

Not finding what you are looking for?
Roper RAS6233KQ Top Load Washer Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roper Washing Machines Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Mike

Level 3 Expert

4356 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Roper Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...