Question about Compaq Presario 5000 PC Desktop

1 Answer

My pc won't start up

I try to start my pc.. the hardware is on but the monitor is blank screen with blinking cursori tried to start again but samething happen..

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 383 Answers
Re: my pc won't start up

MS-DOS ansi.sys command help ESC[2J, Erase Display: Clears the screen and moves the cursor to the home position (line 0, column 0). ... 5, Blink on. 7, Reverse video on. 8, Concealed on ...
NTOSKRNL.EXE is missing or corrupt. When this error occurs your computer will have the error message as shown below. OS Loader v4.01 Disk I/O error status=00000001 Windows NT could not start ...
Good Luck......Please dont for get to Vote.Thank you

Posted on Dec 14, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Vsonic flat screen monitor need blink codes

hi do you mean you are asking for the blinking codes on your viewsonic pc monitor?. usually lcd monitor for pc has no blinking codes, if your monitor just only a blinking indicator and won't turn on, you must check first the source from your pc if their is a signal to turn on the monitor. if just blinking only then won't turn on you must check the power supply of the monitor usually the main cause is bulging capacitor. just replace it with the same value and rating thanks for consulting the fixya good luck.

Feb 26, 2012 | PC Desktops

1 Answer

Monitor displaying purplish colour and sometimes blinks

Have you checked the cable that connects from PC to monitor ? If its VGA, it will be a 15 pin cable. please check both ends of the cable if any PIN is broker or bended. or remove it and tight it again. If that does not solve, the monitor will have some hardware issue.

Mar 03, 2010 | PC Desktops

3 Answers

While installing windows xp monitor went blank, cd started to blink and would not open. I was useing a crt monitor at the time due to the fact thats alli had. HELP, what's wrong

Turn off the computer. Try unseating and reseating the memory one stick at a time in each slot one at a time. After each reseat of the memory try turning on the computer and see if you get video back on the screen.

If not then try another monitor. If all that doesn't get video back on the screen then the motherboard is bad in the computer.

Nov 26, 2009 | Dell PC Desktops

2 Answers

Screen goes black. the power light is on, but the picture goes out. if i turn the power off, then on again it comes back for about 5 seconds, then goes black again.

Check to see if this problem follows in safe mode. Reboot and when the Dell splash screen comes up tap F8 until you see the multiboot options. Scroll to "safe Mode with Networking" let the machine boot up and see if you have a screen. If you do, right click on the desktop and set the resolution to 800 X600 and reboot normally. Usually when a screen goes blank in normal mode but shows up in safe mode means you have an incompatible resolution for the monitor or graphics adapter. This may be a driver issue or hardware. If the screen boots up in normal mode at the lower resolution, then try and go to properties again and bump the resolution up a bit, if it blanks again, try to go online and update the driver for the graphics chip.

Sep 08, 2009 | Dell Dimension E510 PC Desktop

2 Answers

Monitor displays breifly then goes to blank screen

If tried the monitor on two other computers with the same result -- definitly your monitor is faulty. Take it to the repair shop. To make double sure, run your computer with another monitor. If everything is fine now; you can blame the monitor.

Dec 17, 2008 | Dell Dimension 4600 PC Desktop

1 Answer

Blank screen and no lights on keyboard and mouse

*check the power cables

*check the power outlet

*check smps is fine

*check power switches are properly connected

*check in bios hdd is enabled

*open the case wheather the connections are properly connected

Jun 27, 2008 | Compaq Presario SR1103WM-B (PC183B#ABA) PC...

1 Answer

Black screen when i turn on computer.

Do a power drain :- Disconnect every cord from the back of computer tower while the pc is oiff and then press and hold down the power supply button in front of the tower..
have u tried updating the bios any time before?
Secondly,is it possible to go to the safe mode or the screen goes blank even before that?

Jun 27, 2008 | Compaq Presario SR1103WM-B (PC183B#ABA) PC...

1 Answer

Blank screen with blinking cursor

Hello there, Kat4u
Happy Holidays
sometimes, BIOS, RAMS, and Failing motherboard, is the culprit for this problem. have to check that first.
and if this 3 frieds are bad, it is time to change the motherboard.
good luck

Dec 14, 2007 | Compaq Presario 5000 PC Desktop

Not finding what you are looking for?
Compaq Presario 5000 PC Desktop Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Compaq PC Desktops Experts


Level 3 Expert

5660 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Compaq PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides