Question about Indesit WA 125 Front Load Washer

1 Answer


When starting a program, it starts to fill but the pump also runs. It then flashes the red light and the green light above EAST IRON. Any idea's please?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert who has answered 200 questions.

  • Expert
  • 244 Answers

What u can check is the outlet hose does it go down a plastic pipe if so pull it up slightly until it stops a simple mistake if its gone down slightly too much what happens is if its low down the pump kicks in as it thinks the pipe is lower then the washer to drain it try it if i isnt this then it will more then likely be a faulty timer which u will have to replace m8 let me know how it goes m8

Posted on Dec 14, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Blinking lid locked light and green sensor light on machine won't start cycle

The good ol' Whirlpool Lid Lock Flashing Light Problem - ApplianceBlog

Dec 11, 2013 - 10 posts - ‎3 authors
Red Lid Lock light flashing intermittently when you try to start a cycle. ... I'm going to post what SENSING does first, then you will need to locate your tech. ... start with thelid lock on and blinking, or the unit will not start and spin. FIXED Sense light on light humming noise won't start ...
8 posts
Aug 9, 2015
Whirlpool WTW4950XW not working
10 posts
Nov 2, 2013
Stacked GE washer/dryer lights Blinking doeent start at ...
5 posts
Feb 20, 2012
More results from

Washer Sensing led (Green) on with the lid locking led (Red ... > Manage My Life > Questions
... this: Sensing led (Green) on, the lid locking led (Red) blinking with a clicking noise ... red led light goes off green led light stays on and the washer does not start.

Oct 27, 2015 | Washing Machines

1 Answer

I have an Indesit Washer/dryer (WIDL 126 S), and it is dot draining the water. I set in on drain or dry and nothing happens, it just fills with more water.

Check back of washe with a flashlight for a bent or clogged drain hose. Do not move washer to check it. When you move it , it will straighten out and you will never know if it was bent
Also while it is pumping , pick up end of drain hose at drain and observe the volume of water being pumped.
If no water then the Pump needs replaced.
Thank you for using fixya
Leo Ponder
Please rate me if this helped

Aug 12, 2011 | Washing Machines

1 Answer

Indesit WIDL 106 wont start -ON/OFF-Door Led Flashes rapidly

It is a defectiv controller pcb. I think the eeprom on the controller pcb lost its program (happens often on Indesit machines).

The only solution I know is to change the controller pcb, - not a cheap solution.
I have the same problem with WIDL 106.

Dec 01, 2008 | Indesit W 123 Front Load Washer

1 Answer

Wiring for Indesit Widl 126

Tell me, is the machine compleatly dead or what is it doing?

Sep 10, 2008 | Indesit WA 115 Front Load Washer

2 Answers

Indesit widl 126 s washer/dryer wont drain

Ive fixed my problem by turning it on, and after it does the standard pumping part pull out the power plug. Then when you plug it in again it will completely drain and its all reset again.

Aug 28, 2008 | Washing Machines

1 Answer

Indesit WIDL 102

almost certainly a new module and eprom. these modules have given a lot of problems.

not really worth doing

Jun 25, 2008 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Indesit WA 125 Front Load Washer Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 2 Expert

75 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides