Question about NEC MultiSync MT830 Multimedia Projector

2 Answers

NEC Projector I have an older model LCD Data projector. It was workin fine last night, then today nothin. Its like a fuse has gone. The power light doesnt go on once plugged in. do they have a accessible fuse?

Posted by on

Ad

2 Answers

I think you have to Reset the lamp every 800hrs or 1900hrs I think you are to late now just get a new lamp.

Posted on May 01, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

They have a fuse on the power board inside the projector itself, But normally the fuse does not go bad unless their is a dead short in the unit.

Posted on Mar 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEC WT610 Projector powers up and acts like normal, but will not project an image or the usual blue screen with menu functions. Bulb is fine and lights up, no error lights showing. It's as if it's stuck on...


1,Check the fans ,whether each fan is running,when you turn on the projector
2,if the fans run, then ,check the lamp or lamp ballast

Have a nice day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel,
motherboard, powersupply ... with high quality and competitive price.
Jerry
Lampdeng Limited

Feb 05, 2015 | NEC Office Equipment & Supplies

2 Answers

The projector turns on but won't project any light through the lens.


If this is a NEC VT series projector, Change the lamp. When if it continues to blink amber and not project and image after installing a new lamp check the lamp cover to see if the micro switch tab on the lamp cover broke off. Some models have a built in lens cover. If the cover is not slid over to open completely the light may not turn on.

May 19, 2014 | NEC VT800 LCD Projector

1 Answer

My nec mt810 lcd projector is showing some green colour not sharp colours showing whats problem plz help


It seems that the lcd panels are failed
Have a nice day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel,
motherboard, powersupply ... with high quality and competitive price.
Jerry
Lampdeng Limited

Oct 14, 2013 | NEC USHIO PROJECTOR LAMP, Projector Lamp...

1 Answer

NEC vt800 projector troubleshooting


That is a problem with the lamp. Replace it with a known good one.

Feb 27, 2013 | NEC VT800 LCD Projector

1 Answer

My NEC vt 595 was working fine last night and today i went to turn it on the status and power light started flashing red and orange and there is no picture


if Power is flashing orange - then it's cooling down

if Status is flashing red - then there are 4 flash combinations.
1 cycle (0.5sec On, 2.5sec Off) lamp cover or housing error
2 cycle (0.5sec On, 0.5sec Off) temperature error
4 cycle (0.5sec On, 0.5sec Off) fan(s) error
6 cycle (0.5sec On, 0.5sec Off) lamp error

Which is your condition?

Mar 18, 2011 | NEC VT595 LCD Projector

3 Answers

I have replaced bulbs in 3 different types of NEC projectors: a silver, older model thta uses a VT60LP bulb, model VT595 and VT470. The lamp will still not work - the power and status light just continue...


I had the same issue, what I figured out was that I never removed the lamp door correctly, causing a small plastic piece to break off. To see if this is also your problem, inspect the back of the lamp door, top right corner, if it seems a rectangular plastic piece is missing, thats the problem. It presses in a small button nearby the lamp to let the projector know it's safe to power on.

I've attached an image to help out.ea22ca6.gif

Sep 01, 2009 | NEC VT695 LCD Projector

1 Answer

My Sharp XG-E650UB does not power on or show power indication.


Have a nice day!
We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel,
motherboard, powersupply ... with high quality and competitive price.
Jerry
Lampdeng Limited

Aug 23, 2009 | Sharp PROJECTOR LAMP, Projector Lamp FOR...

1 Answer

NEC VT695 (not a vt570) bad lamp blowing ballast board?


We have the same model here at our school too. I know of two that have done exactly what you said. I am trying to figure out if this is NEC fault. Bulbs are expensive and if the projector and NEC is a fault; we will definitely be moving on to a different brand.

Oct 03, 2008 | NEC VT570 Multimedia Projector

1 Answer

Power does not work


ok " always check power first, sounds like internal fuse
has blown , just has to be replaced.

Jan 20, 2008 | Optoma MovieTime DV10 Multimedia Projector

Not finding what you are looking for?
NEC MultiSync MT830 Multimedia Projector Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2237 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a NEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...