Question about Maytag MFD2560HES Bottom Freezer French Door Refrigerator

1 Answer

Maytag ice20 hi i replaced the high voltage control board but need help programming it

Posted by on

  • Anonymous Dec 16, 2007

    The electronic board has gone out three times in four months. There is a second generation board-that has been replaced twice. We are under warrenty but have lost thousands of dollars in food. And Maytag Amana does not exist. They were bought out by Whirlpool who takes no responsibility.

  • maytaghater7 Oct 08, 2008

    My MBL2562KES has the same problem. Can't get the Hv board reprogrammed. Tried these very helpful instructions but couldn't get the code entered and now it's like I am locked out. When I hold the door alarm button down then the freezer minus button then release the door alarm button nothing happens. It won't even let me try to enter a code! Any way to reset this so I can try again? Is there hope? Hv board is brand new. So is digital display board. Thanks.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

When replaceing the highvoltage control board be careful to not handle it too much as nano voltages can burn it. Unplug before repair. Simply hook it up the way you unhooked it very easy and in the left back of the fridge. Now that it's installed plug fridge in and push back to wall. Look at model tag and write down your code something like 0304 most likely. Go to digital control hold down door alarm and freezer - minus button for 3sec. then let off door alarm now you should see PE flashing the fridge wants personality code (the one you have wrote down). Let off minus now it should show 0000 now push minus once more a decimal should show up 0.000 the decimal indicates what number your about to change. Move the decimal with freezer plus button and lower or higher number setting with fridge side buttons.Once your done hold down freezer minus till the numbers are flashing then open any door and close. Now the fridge should be working properly.Hope I helped

Posted on Jan 20, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is control panel flashing as though possessed?


need a high voltage board, when replacing the board on the back of the refrigerator make sure to unplug and program according tothe instructions that comes with the new one

Jan 07, 2016 | Maytag Refrigerators

2 Answers

What is wrong with my Maytag refrigerator


You have a bad high voltage board call the manufacturer, if the unit is under 2 yrs old they may help cover the repair with the problem your having.

Jul 30, 2008 | Maytag MFI2568AES Stainless Steel Bottom...

2 Answers

Maytag Ice20 refrigerator


You have a bad high voltage board and as the other user said call the manufacturer they are assisting with this problem.

Jul 09, 2008 | Maytag MFI2568AES Stainless Steel Bottom...

3 Answers

Mayteg refirgerator


French Door “ICE-2-0” Bottom Mount
Freezer Refrigerators with
Ice & Water Dispenser
Maytag Models: MFI2568AEB MFI2568AEQ MFI2568AEW MFI2568AES MFI2067AEB
MFI2067AEQ MFI2067AES MFI2067AEW
Amana Models: AFI2568AEB AFI2568AEQ AFI2568AES AFI2568AEW
cusTOMeR COMPLAINT:
Ice dispenser door continually opens and closes and/or user display flashes on and off intermittently.
cause:
Power supply circuit on high voltage control board may fail.
cORECTION:
Order and install high voltage control board kit PN 12920710. The kit includes; control board, installation and programming
instructions, return label and card for the old part.
Note: As with all Refrigerators of this type, the correct “Personality Code” must be programmed into the new control board
per the instruction sheet provided.

Feb 16, 2008 | Washing Machines

4 Answers

Panel flashing, ice door opening and closing constantly


I had the same problem, with this model and it was the high voltage control board located in the rear. Replaced the board and it is working OK. Maytag Part # 12920710 will work on this model and it is 40.00 cheaper than the one it shows when you do a parts search. It will come up 12920709. I checked with Maytag and they said 710 will work..

Sep 23, 2007 | Maytag MFI2568AE Side by Side French Door...

2 Answers

I found the problem and the answer to my problem BUT the part is backordered and I am wondering


See the post on Samurai Appliance Repair Man's site http://applianceguru.com/forum1/13035-1.html for instructions on how it's possible to fix the HV Controller Board power supply filter caps for $5 in Radio Shack parts (really!). You need to be able to solder electronic components, or know someone who can. There are 2 power supply filter caps that appear to go bad and the result is the blinking and flapping. I had the same problem and decided I could not wait for a $150 replacement back-ordered board.

Jun 19, 2007 | Maytag MFI2568AES Stainless Steel Bottom...

2 Answers

Maytag French Door Refrigerator with ice and water on the door


See the post on Samurai Appliance Repair Man's site http://applianceguru.com/forum1/13035-1.html for instructions on how it's possible to fix the HV Controller Board power supply filter caps for $5 in Radio Shack parts (really!). You need to be able to solder electronic components, or know someone who can. There are 2 power supply filter caps that appear to go bad and the result is the blinking and flapping. I had the same problem and decided I could not wait for a $150 replacement back-ordered board.

Jun 17, 2007 | Maytag MFI2568AES Stainless Steel Bottom...

Not finding what you are looking for?
Maytag MFD2560HES Bottom Freezer French Door Refrigerator Logo

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Refrigerators Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Carlos Alvarez

Level 1 Expert

8 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...