Question about Hotpoint 23 in. BFI68 Built-in Dishwasher

1 Answer

All my lights are on!

as of this morning, every light on my dishwasher control panel is constantly on and I can't do anything to start the dishwasher.
Any ideas? I'm happy to replace a part if you can tell me which one

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 126 Answers
Re: All my lights are on!

Turn breaker off and on to see if it resets if not it could be your control board.

Posted on Dec 12, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Kid 60 s10 please give fault codes

Hi Roger, Hope this helps......CHEERS..


Kenmore Dishwasher Error Code = Start Resume light blinking slow
When the dishwasher door opens or electrical power is removed during the cycle then the dishwasher will not start again. The door is detected as being closed and the Start Resume button is being pressed
Kenmore Dishwasher Error Code = Clean light is blinking 7 times
Heater circuit fail. Control panel did not detect the water getting hot. Did not detect heating element was energized to heat the water during the wash cycle
Kenmore Dishwasher Error Code = Sanitize LED blinking at end of cycle
Control panel could not detect if sanitation has been achieved
Kenmore Dishwasher Error Code = Console light blinking rapidly
There is a stuck button on the control panel
Kenmore Dishwasher Error Code = Clean light is constantly illuminated
Dishwasher cannot start a wash cycle until it sees that the door has been opened after the previous washing cycle
Kenmore Dishwasher Error Code = Control lock LED is ON but not responding to pressing of the keys
Turned on by accident or there is a control detected key pad problem

Mar 31, 2016 | Kenmore Dishwashers

1 Answer

Why is heated dry blinking?

FIXED Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry ...

Aug 26, 2013 - 10 posts - ‎3 authors
Thread: Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry" ... A few months ago, we had a brief power outage and the next morning, noticed the "Hi Temp" and "Heat Dry" lights were flashing. ... Well since then, the dishwasher intermittently stops mid-cycle and these same lights ... Thread: GE Eterna QuietPower 2 Normal and Heated Dry ...
6 posts
Feb 24, 2012
Kenmore Elist 665 dishwasher Smart Wash red light ...
6 posts
Dec 23, 2011
Heated dry blinking +17 times - ApplianceBlog
10 posts
Nov 14, 2010
Heated Dry light blinking
3 posts
Nov 7, 2010
More results from

Why won't my dishwasher start and why does the "Heated Dry" > Manage My Life > Questions
Nov 16, 2009 - When I hold down the Heated Dry button to turn the control lock on it dishwasher start and why does the "Heated Dry" light keep blinking ...

Dec 01, 2015 | Dishwashers

1 Answer

Electrolux dishwasher not completing wash cycle and all lights flashing on door control panel and the 'wash pump' error light behind the lower kick space panel was flashing.

Good Morning friend, thanks for your post!

After researching the issue you are having with your Electrolux dishwasher it is possible that resetting your appliance may help. I would disconnect power from your dishwasher by unplugging it or flipping the household breaker for roughly ten minutes. If this does not resolve your issue I would recommend seeking assistance from a professional to properly diagnose and repair your dishwasher. -T

Jan 23, 2014 | Electrolux Dishwashers

2 Answers

My GU2475XTVY0 built-in dishwasher has the "Normal" light flushing since yesterday morning. We pressed "Cancel" button, other buttons, and finally turned the power off and on, but it didn't do anything. Do...

Hello- The touch control pad is failing and must be replaced. If unit is under warranty, get it serviced. This control is about 125$. Let me know if this info helps. Thanks-Ed

Mar 08, 2010 | Whirlpool GU2400XTP Built-in Dishwasher

3 Answers

Power to dishwasher but no power to panel

Open your console and check the continuity of the thermal fuse (clipped to the electronic control unit [ECU]).
Post your model number if you're still having problems and I'll try to assist you further.
Good luck!

Apr 04, 2009 | Whirlpool 24 in. GU1500XTLS Stainless...

1 Answer

When trying to start the dishwasher the normal load light,heat light, and other lights blink and nothing happens.

take the control panel off and re-seat the ribbon cable back on the board if that does not change anything replace your control panel.

Feb 20, 2009 | Frigidaire 24 in. FDB1050REC Stainless...

4 Answers

Kenmore elite dishwasher

I had the same problem when I bought it and it just happened again; the problem is solved by ressting the control panel: Hi Temp ---> Heated Dry two or three times. It kind of goes into a testing cycle and the clean blinking light goes off.

Dec 08, 2007 | Kenmore 24 in. 16032 Built-in Dishwasher

Not finding what you are looking for?
Hotpoint 23 in. BFI68 Built-in Dishwasher Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 2 Expert

157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides