Question about Sony PlayStation 2 (PS2) Console

1 Answer

Playstation 2 Version 14 Slimline

Hello i have just changed the laser and carrige with a PVR802W slimline laser and carrige removed the anti-static point as requested by instructions, turned on the console and hay presto it worked again. I then turned if of, then later went to turn it on and suddenly there is no power light on and it wont work can you sugest any thing please.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Try shutting the drive on the right side but keep the left open with a finger if the lens light flashes a few times and goes off theres something wrong with the lens it may be a coil which has burnt out which has caused the whole lens to pack up hpoe it helps!!

Posted on Dec 15, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ps 2 slin not spinning just replace old laser by new one


Sounds like either you got a bad laser, or if the anti-static solder point on the left side of the new laser was not removed with a soldering iron, then the laser will not work. Simply heat it with an iron and maybe some solder wick and you should be good to go.

Nov 27, 2009 | Sony PlayStation 2 Slimline Console

1 Answer

Playstation2 Slimline


1. CLEAN THE LASER. ALWAYS DO THIS FIRST. MOST TIMES THIS IS ALL YOU NEED TO GET YOUR SYSTEM BACK RUNNING A 100% AGAIN

2. IF THE LASER CLEANING DON'T WORK ON YOUR PS2 SYSTEM PERFORMANCE THEN TRY ADJUSTING THE LASER VOTAGE.

3. IF THE LASER VOTAGE DON'T WORK YOU NEED TO REPLACE THE LASER $50-75 CALL FELTON (870) 733-1375 OR EMAIL ME IWHYOU@YAHOO.COM

Aug 06, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

Spindle not working?


If you touch the laser lens with your finger you maybe burned with your static.

May 21, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

Spindle probs?


These replacement parts are shipped with a solder bridge to short the laser as a precaution for static electricity. Did you remove the solder bridge once the optics were installed?
Dan

May 20, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

PS2 Slimline read error


ps2 slimlines had as problem with doing the lasers .this was a fault of over voltage to the laser lense.sony did bring out a mod for this.you would have to replace the laser .they are not all that dear.make sure you get the right one for your model

Apr 26, 2008 | Sony PlayStation 2 Slimline Console

2 Answers

Disk read error on slim ps2 scph 75003


hello pauldonp...if this is an early version of the slimline they had a problem with over voltage which inturn took out the laser.your only option may be to replace the laser . sony did bring out a mod for this..i preferr the real old version of the ps2 as they had all separate boards and if one went faulty you didnot have to replace the lot ,also the lasers were a lot cheaper than the later models .in the slim lines the lasers are not all that expensive .they do take a bit of setting up as you have to know the ohms setting on the laser for each model..hope this helps

Feb 08, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

Playstation 2 slimline


wat did u do to that poor machine!?! i broke something...or, theres a Lego (lol) in the track...open her up, and take a pic...send it 2 me, and ill tell ya from there..kk

ps: jedi_arts_101@yahoo.com

Feb 05, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

PS" Version 12


check to make sure flat cable that connects laser is installed correctly or isnt damaged.

Jan 09, 2008 | Sony PlayStation 2 Slimline Console

1 Answer

Disks wont spin on new laser


Did you remove the anti static solder blob (point) on your new laser with a soldering iron and solder wick prior to installing it? The symptons your explaining indicate that point is still intact, If so you will need to carefully remove it first then reinstall the laser and try again.

Sep 13, 2007 | Sony PlayStation 2 Slimline Console

Not finding what you are looking for?
Sony PlayStation 2 (PS2) Console Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Video Game Consoles & Games Experts

Zhenya Ogorodnikov

Level 2 Expert

218 Answers

shaun taylor

Level 3 Expert

1527 Answers

juanmireles1

Level 2 Expert

219 Answers

Are you a Sony Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...